190gr Nosler Accubond Long Range in 300wsm anybody?

[Rugerdiggs]

Anybody using the 190gr Nosler Accubond Long Range in a 300wsm?
Looked on there website and there not listing any data for it. In hopes someone else is loading it and will have a starting point. I have a few different powders on hand, all hodgdon 4350, 4831sc, h1000, the brass is primed with CCI magnum primers. Any help is appreciated thanks.

Just got the gun in Thursday, put the optics on it and ran 10rds though it cleaning after each shot. Got 90 pieces of brass primed and hope to dump some powder and seat bullets this evening or Sunday evening.

 

[brentc]

Anybody using the 190gr Nosler Accubond Long Range in a 300wsm?
Looked on there website and there not listing any data for it. In hopes someone else is loading it and will have a starting point. I have a few different powders on hand, all hodgdon 4350, 4831sc, h1000, the brass is primed with CCI magnum primers. Any help is appreciated thanks.

Just got the gun in Thursday, put the optics on it and ran 10rds though it cleaning after each shot. Got 90 pieces of brass primed and hope to dump some powder and seat bullets this evening or Sunday evening.

Of the powders you have, 4350, and 4831sc will work very well. H1000 is too slow for the 300 WSM case. 4831sc will most likely get you the best velocity, but don't expect blazing fast. For 4831sc start at 66 and work up. Your load should come in around 67.5 to 68.0 grains. For 4350 start at 62 and work up. Your load should come in around 64.0.

 

[topmoteur]

in my a bolt II i put vn550 61.5 gr with the 190 ablr and average .75 moa factory rifle
average speed 2920

 

[live2huntmt]

I settled on 65.0gr of RL-17 out of my Tikka T3 Lite 300 WSM w/ 190 ABLR's. Norma Brass and Fed GM210M Primers. I have only taken it out to 300 yards but it is producing 1/2 MOA @ 300. COAL is 2.085" to fit in my Tikka Magazine.

 

[Rugerdiggs]

Well I went 0-2 with the H4350 and H 4831sc so I bought some H100V and best of all the powders was in high .9's. Shot a full 100rds of bullets. I switched to 180gr accubonds with 64.0 grains of H100V shooing in .4s. Yesterday I got a chance to stretch it a few yards, shot a 1.7" at 419yds.

 

[Sauer 150]

My go to powders for my WSM is Re 22 and IMR 7828SSC.

SSC behind 180 Scirocco II's and 200 Nosler PT shots under 1" at 300meters in my current rifle.

SCII's at 2950, 200 PT at 2860.

 

[iclick]

Anybody using the 190gr Nosler Accubond Long Range in a 300wsm?
Looked on there website and there not listing any data for it. In hopes someone else is loading it and will have a starting point. I have a few different powders on hand, all hodgdon 4350, 4831sc, h1000, the brass is primed with CCI magnum primers. Any help is appreciated thanks.

Just got the gun in Thursday, put the optics on it and ran 10rds though it cleaning after each shot. Got 90 pieces of brass primed and hope to dump some powder and seat bullets this evening or Sunday evening.

Nosler lists load data for that bullet on their website now.
300 Winchester Short Magnum (WSM) Load Data - Nosler
The better powders seem to be:
Norma MRP
IMR 7828 ssc
and Alliant 4000-MR
I use it in my custom built 300wsm AR10 with a 24" BBl behind 64GR of the 4000-MR. Group is consistent at within 1/2 inch at 200 yards. Avg velocity is 2,933fps. COL is to mag length at 2.799"

 

[livtoohunt]

I am loading 190gr Bergers with H4831sc at 2.84 and have had great accuracy. Haven't run it through a chrony yet but expect 2800-2850.

 

[slydo440]

I settled on 65.0gr of RL-17 out of my Tikka T3 Lite 300 WSM w/ 190 ABLR's. Norma Brass and Fed GM210M Primers. I have only taken it out to 300 yards but it is producing 1/2 MOA @ 300. COAL is 2.085" to fit in my Tikka Magazine.

2.085" looks like a bit short no? Maybe you mean 2.850" ?