Tumbling loaded ammo?

I guess I would ask "WHY" ?

Prepare your brass before you load it and don't take a chance with changing burn rates.

Powder burn rates are controled by shape and size and the coating(A Stabilizer in most
cases) and changing that can be detrimental to the performance.

Think about how many times the case gets shook or tumbled in order to remove the patina/
corrosion on the outside of the brass.with an abrasive media. Powder is not subjected to this
amount of vibration in its lifetime of shipping and handling.

Media wears out with use and produces lots of dust in the process of tumbling and powder
will do the same. I'm sure that different powders will break down at different rates,So again
WHY take a chance.

We all have had different batches of the same powder burn at different rates and the formula
is the same for that particular powder so what has changed ? the shape,hole diameter,coating
thickness ETC.

So I a person wants to tumble or vibrate a loaded round ,It is his choice but common sense
alone should tell you it is not a good practice. It is best to error on the side of safety.

Enough said.

J E CUSTOM
 
Post #6 has the answer.

When I first heard that idea some 30 years ago, I too decided to err on the side of caution; that's never a bad thing to do. But then reason kicked in; I "tested" a few mixed cartridges - rifle/handgun - with different powders. Removed half after an hour, pulled the bullets and examined the powder, turned the tumbler back on and left the rest to run over night. Couldn't see any difference between the powders in either batch and new powders. Seems the action of my Lyman 1200 tumbler is was too gentle to damage my powders. YMMV.
 
As others have said "DONT DO IT"

If it needs to be cleaned use some steel wool and do them by hand.

The problem with tumbling loaded rounds is that it wears the powder down and produces a
fine dust that burns a lot faster than the original powder granules making the same ammo
very dangerous.(Higher pressure).

Shoot it like it is, and if it has corroded spots on it like lots of the old military ammo toss it
because it could fail and damage your chamber.

J E CUSTOM
+1 on the steel wool! Very rarely do I even tumble at all. steel wool is easy, fast and gives it a cool "brushed" look
 
Knew a guy that use to buy huge quantity of old Military ammo that would be green and grungy. He bought a cement mixer and would fill it half full of sand and then through in a bunch of this ammo. Stuff looked great when he finished with it and every now and then one would bang off and make the neighbors nervous. They even called the cops a few times but never did anything about it. Small town and he supplied the PD with their ammo. :) FREE.
He would then re-box the ammo and sell it at gun shows. One reason I never buy ammo at a gun show. Did this for years and the only complaint he had from his customers was you would end up with about 5 -10 duds in every box. Thus the reason he sold it cheap.
 
I use H322-335 in my match rounds and I've not observed any change in accuracy or behavior in the handloaded rounds.

I use a single stage (Rockchucker) for loading, not that I progressive would make any difference. It's finished ammunition before storage....

I'll keep on with my procedure, works fine for me.

To each his (ir her) own.....
 
I think that a lot of us wont tumble finished ammunition because it takes us back to the military surplus and rock tumbler days. I do not use this practice but honestly can not say that I never will. There are several reasons why I do not but on this subject if a guy wants to put his ammo in a wool sock and bury it under an Oak Tree during a full moon then go ahead and do it if it works!
 
The only reason I wanted to do it is because I have a box of about 70 rounds of some older ammo. I'm not the luckiest guy so I think I'll try the steel wool and try to clean them by hand, although I may do some experimenting and check before and after powder conditions out of curiosity.

Thanks for the plentiful help.

Ryan
 
The only reason I wanted to do it is because I have a box of about 70 rounds of some older ammo. I'm not the luckiest guy so I think I'll try the steel wool and try to clean them by hand, although I may do some experimenting and check before and after powder conditions out of curiosity.

Thanks for the plentiful help.

Ryan

Do some Google searches and you should find some guys that have already done the testing. I would post some links but I am at the range right now.

T
 
Depends entirely on whether the vehicle has square tires or is driven on Michigan (potholed) roads......:)

I never knew why Monroe Shock Absorber was located in Monroe County, Michigan until I mover here. The colunty is a test track for shock life......

Amen to that. I was just up in Temperance and Sylvania OH visiting friends and relatives for Christmas...boy I forgot how bad they get...

Matt
 
It can be done. I wouldn't do it myself.
Go to Wally world and get a bottle of Brasso metal polish, wipe em down.

If you have no more use for the brasso, dump it in your tumling media.
Miles
 
Do some Google searches and you should find some guys that have already done the testing. I would post some links but I am at the range right now.

T
Ditto on this one, there's a fellow over on AR15.com who did extensive testing on tumbling live ammo. In long term tumbling, "something more than 24hrs" There was only the slightest surface change to powder granuals "viewable with a microscope" and it resulted in no or very little measure in performance.
Some people say don't do this or that sometimes just because they want to have an oppinion. You could always tumble a few loaded rounds for 24 then 48hrs to find out just how long it does take to actually damage a powder granual.
 
Warning! This thread is more than 13 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top