Question on CBTO measurement

Personally if it were me I'd jump them farther than the .020 your mentioning. All of my experience with the Hybrids of varying calibers have shown they like to jump farther. I've had great results in the .050-.070 area of jump and have shown less pressure here also. I jump some even further than this.
 
Last edited:
Personally if it were me I'd jump them farther than the .020 your mentioning. All of my experience with the Hybrids of varying calibers have shown they like to jump farther. I've had great results in the .050-.070 area of jump and have shown less pressure here also. I jump some even further than this.
Thanks for the intel regarding your experience with Hybrids & the jump. I'll plan on running some test loads with various options....0.050 etc...
 
You would think that CBTO is CBTO, once you know what the distance is from bolt face to the lands it would be the same for all bullets when seated to that distance using CBTO to seat bullets, only difference would be the COAL due to different bullet shapes, i.e. some with longer pointed noses or shorter rounder noses. And then the magazine length comes into play.
 
I would put them off the lands were ever they shot the best, every gun, barrel, bullet and caliber is different.
Only way to find out is test and not at 100 yards, minimum 500.
 
You would think that CBTO is CBTO, once you know what the distance is from bolt face to the lands it would be the same for all bullets when seated to that distance using CBTO to seat bullets, only difference would be the COAL due to different bullet shapes, i.e. some with longer pointed noses or shorter rounder noses. And then the magazine length comes into play.
Except not all bullets have the same profile whether they are tangent or secant ogive. The ogive to base varies on all bullets.
 
Except not all bullets have the same profile whether they are tangent or secant ogive. The ogive to base varies on all bullets.

Correct. I read about this in detail some time ago as bolt face to lands is a constant measurement. As I understood it the variable comes in from the nose angle of the bullet and how and where it comes in contact with the lands/leade. Quoted below is a good brief explanation I read about on a discussion on loading for a 308 and why it varies.

" The lands are less than .308 in diameter. There is a conical "ramp" going from the .308 freebore to the uncut lands (the leade). This is where the bullet makes contact. And where the bullet makes contact on the leade depends on the angle of the leade and the shape of the bullet."
 
Last edited:
Correct. I read about this in detail some time ago as bolt face to lands is a constant measurement. The variable comes in from the nose angle of the bullet and how and where it comes in contact with the lands. Quoted below is a good brief explanation I read about on a discussion on loading for a 308 and why it varies.

" The lands are less than .308 in diameter. There is a conical "ramp" going from the .308 freebore to the uncut lands (the leade). This is where the bullet makes contact. And where the bullet makes contact on the leade depends on the angle of the leade and the shape of the bullet."
Agree 100% that why you get different measurements for different bullets same caliber & rifle.
 
The same weight bullet by different manufacturers, or even the same manufacturer, that makes several different bullets of the same weight and caliber can be different. It depends on the radius of the ogive and the bearing surface length which can vary from bullets of the same weight and different weights. From what you described, you should be fine for your starting point, but don't expect it to be the exact point at which your rifle will like the heavier bullet to be seated.

This might make more sense...
 
Last edited:
Correct. I read about this in detail some time ago as bolt face to lands is a constant measurement. As I understood it the variable comes in from the nose angle of the bullet and how and where it comes in contact with the lands. Quoted below is a good brief explanation I read about on a discussion on loading for a 308 and why it varies.

" The lands are less than .308 in diameter. There is a conical "ramp" going from the .308 freebore to the uncut lands (the leade). This is where the bullet makes contact. And where the bullet makes contact on the leade depends on the angle of the leade and the shape of the bullet."
So if the "ramp" is 30°, 45°, or 60° and the different ogive designs there could actually be up to 0.0xx" difference in CBTO to where the bullet actually touches the lands. Is that ramp angle set by SAAMI or the cartridge developer? Rifle manufacturer or gunsmith can change that as they wish? I checked a 30Nos SAAMI drawing I have on hand and it shows 45° for that ramp, followed by 0.110" of 0.3091" then a 1° 30' taper(the leade?) for a distance of ~ 0.1738", then the bore and groove.
 
Last edited:
So if the "ramp" is 30°, 45°, or 60° and the different ogive designs there could actually be up to 0.0xx" difference in CBTO to where the bullet actually touches the lands. Is that ramp angle set by SAAMI or the cartridge developer? Rifle manufacturer or gunsmith can change that as they wish? I checked a 30Nos SAAMI drawing I have on hand and it shows 45° for that ramp, followed by 0.110" of 0.3091" then a 1° 30' taper(the leade?) for a distance of ~ 0.1738", then the bore and groove.

In most cases from what I understand the ramp in most is 1.5 degrees. I'm not an expert by any means but here's a article from Lilja the barrel experts that does a great job of explaining it. Sorry if we're derailing the OPs thread.

 
In most cases from what I understand the ramp in most is 1.5 degrees. I'm not an expert by any means but here's a article from Lilja the barrel experts that does a great job of explaining it. Sorry if we're derailing the OPs thread.

Don't worry about the OP's thread (me) this intel is very informative & I'm sure
others enjoy it as well.
 

Recent Posts

Top