I'm getting ready to build an 8 ft long reloading bench and was wondering if I should leave a 4 inch overhang in the front. I think it may help keep the knees from bumping up against the lower shelf. I also plan to use the Ultra Mount from In-line Fabrication so the overhang is not absolutely necessary. Any advice is much appreciated.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Reloading Table, Overhang Top or Not?
- Thread starter tbailey1
- Start date
Help Support Long Range Hunting Forum
scpaul
Well-Known Member
It makes it easier to mount your presses and tools provided that you build it strong enough so that it doesn't flex under load. I built my bench tops from 2x6. I have a 6" overhang and wish that I'd built more, 1ft possibly more. I can't sit up close enough unless I sit at an angle. Pulling on a press handle hard like for case forming is uncomfortable.
FrogFire7
Well-Known Member
Mine doesn't have an overhang, but I have mine open under the press (no shelving under). I also have a cabinet door under my single stage, so I guess I have it both ways. I don't really see a difference.... Mine is 2x4 frame and 3/4" plywood top. If anything, I wish I'd gone heavier on the top, mine flexes.
Mike Matteson
Well-Known Member
In-Line-Fabrication work great for me. I use and will again use a 3'x6'8" solid core door as the top of the bench. You can add a steel plate under the press area to reinforce that area. Put the shelving to one side for storage. Leaving room for you legs. You will want to set the table up dead level both ways.
I had in the past set up a line to do my reloading. With the In-Line-Fabriction plates that stop the need for additional bench to attach other items or far less.
So I figure that I don't need an extend bench to reload with. I will need shelving to store my equipment in. Being the reloading equipment is on plates to move on or off the set up. That going to take some storage area for that. So somethinbg to think about.
I had in the past set up a line to do my reloading. With the In-Line-Fabriction plates that stop the need for additional bench to attach other items or far less.
So I figure that I don't need an extend bench to reload with. I will need shelving to store my equipment in. Being the reloading equipment is on plates to move on or off the set up. That going to take some storage area for that. So somethinbg to think about.
Mike Matteson
Well-Known Member
Add a steel plate under it and the bench. Lag it in. and drill holes where needed. The plate needs to extend back under the table to gain strength.
Hugnot
Well-Known Member
My bench has a 2X6 under 3/4 plywood to provide an overhang for my press. 2X6 & 3/4 plywood glued then clamped then 2-inch deck screws. Plywood covered with surplus 5/8 wood flooring. Supporting bench legs are under 2X6, plywood, & surplus flooring - 3 1/2-inch overhang including 3/4 facia.
M1A1ABRAMS
Well-Known Member
I thought there was a thread on here. Where people showed their reloading rooms & benches. It was about the time I first signed onto this forum. But I have looked & can not seem to find it. They really had some awesome ideas. From space saving ideas. To how they built their benches & rooms. I really wish someone could steer me to that thread wherever it may be ? I really liked the roll top desk someone used for a space saver idea. And it was so clean & out of sight (not visible to wandering eyes). And then a few others were using doors for bench tops, because it was cheaper than butcher block or building a top. A lot of them used the In-line systems also. I would have to say it was the best thread I ever spent my time looking at. The imagination used by some was just simply beautiful. I believe this was when Primal Rights built his own cabinets for his room. Any reference to this thread would be greatly appreciated.
scpaul
Well-Known Member
Mr. Abrams, I remember that thread and thinking that a spotless bench is a sign that it isn't used much or how long did it take to clean it up?
Jokes aside, I couldn't find it either and I know it existed.
Jokes aside, I couldn't find it either and I know it existed.
M1A1ABRAMS
Well-Known Member
Birddog 68 steared me in the right direction. There are actually a few different ones. But I believe this is the one I was referring to.
Reloading setups
Well, it’s been about 20 years since I’ve got into reloading and it has taken all of that time to acquire what I have. I have found there is always something else to add to the list. Hoping to add onto this table soon as I have been out of room for years but have not got around to making time to...
Homemade reloading benchtop material?
The time has come and the wife has green lit my reloading bench project for the new house. Was walking through Lowes today looking at material and got to wondering what you all are using as a bench top? My only friend who reloads swears I need a thick butchers block top to handle the torque of...
Last edited:
scpaul
Well-Known Member
That's it, sickening ain't it. I wish mine looked like that.
Bucklowery
Well-Known Member
My bench has no overhang but is perfect for my rcbs press. When I added the lee press for crimping I built a metal angle to push away from table. The handle works differently and needed clearance but it is over built and lagged to the 2x6 edge
Thanks
Buck
Thanks
Buck
Appreciate everyone's comments. Next question is how deep would you recommend not counting cabinet space?
I have a 25 inch deep by 8 ft long butcher block I plan to use for the table top. I plan to add a couple stacked 3/4" plywood behind the butcher block for cabinet space. The depth of those will depend on how much overhang I have with the Butcher block. That's my "preliminary plan".
I have a 25 inch deep by 8 ft long butcher block I plan to use for the table top. I plan to add a couple stacked 3/4" plywood behind the butcher block for cabinet space. The depth of those will depend on how much overhang I have with the Butcher block. That's my "preliminary plan".
scpaul
Well-Known Member
Mine is 24" wide and I used children's book cases that are 6" deep for my shelves behind my work surface. I got mine from a second hand store. They're solid wood and cheap, simple and stable no matter how much weight, loaded ammo, components, tools, presses (big ones are heavy), etc. I didn't put doors on mine so I can see everything instead of searching for thi gs that I don't use but once in a blue moon. By the way, mines a terrible mess but that's my fault.
