• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

Pressure?

The_Whitetail_kid

Well-Known Member
Joined
Aug 28, 2021
Messages
287
Location
Texas
Hello everyone. Need some help here. I have shot 3 loads today at the range, and all three caused some sticky boat lift. I don't feel like the power charge is that high, and I'm not good at telling pressure signs by looking at the bottom of the case. In my 7RM. Thanks
 

Attachments

  • AC69049A-A560-4EEF-9BFA-8195BB315B4E.jpeg
    AC69049A-A560-4EEF-9BFA-8195BB315B4E.jpeg
    1.3 MB · Views: 687
  • B88501AC-C4B3-4C90-A918-6E89F7C8414C.jpeg
    B88501AC-C4B3-4C90-A918-6E89F7C8414C.jpeg
    828.3 KB · Views: 679
  • 6B722BFD-3CA9-4D71-8727-14ECBA32CE05.jpeg
    6B722BFD-3CA9-4D71-8727-14ECBA32CE05.jpeg
    1.3 MB · Views: 680
Last edited:
Tell us more info. New or fired brass, clean chamber? What is your jump to lands? What gun? I've had some stickers from just a dirty chamber. New brass can do some wierd stuff sometimes. I personally don't see anything jumping out about the brass. A little crater maybe but if your bolt has a smidge bigger firing pin hole that could be where that came from. The primers don't look flat at all. Could also be from way undercharged load. You did say you didn't think it was too high. Anyway, tell us more detail.
 
Hello everyone. Need some help here. I have shot 3 loads today at the range, and all three caused some sticky boat lift. I don't feel like the power charge is that high, and I'm not good at telling pressure signs by looking at the bottom of the case. In my 7RM. Thanks
What bullet and weight, powder, and charge? The more pertinent information you can provide, the better.
 
Tell us more info. New or fired brass, clean chamber? What is your jump to lands? What gun? I've had some stickers from just a dirty chamber. New brass can do some wierd stuff sometimes. I personally don't see anything jumping out about the brass. A little crater maybe but if your bolt has a smidge bigger firing pin hole that could be where that came from. The primers don't look flat at all. Could also be from way undercharged load. You did say you didn't think it was too high. Anyway, tell us more detail.


Sorry for being vague. Fired brass, and clean chamber. Christensen arms ridgeline 7mm rem mag. One load 69 grains h1000 160 accubond. One load 70 grains h1000 with 160 accubond, one is 71.6 grain retumbo, 168 Berger. The bergers were seated 30 thousands off and accubonds 20 thousands off. Not that it matters but the 70 grains h1000 with accubond and 71.6 retumbo both shot half inch groups.
Norma brass, cci 250 primers.
 
Sorry for being vague. Fired brass, and clean chamber. Christensen arms ridgeline 7mm rem mag. One load 69 grains h1000 160 accubond. One load 70 grains h1000 with 160 accubond, one is 71.6 grain retumbo, 168 Berger. The bergers were seated 30 thousands off and accubonds 20 thousands off. Not that it matters but the 70 grains h1000 with accubond and 71.6 retumbo both shot half inch groups.
Norma brass, cci 250 primers.
is this a new rifle?
 
the first 2 pics it looks like the primers still have a rounded edge. The thrird on is flatter but they all look like they have ejectors marks to me
I thought I might see what looks like that too, but it uncannily appears to be in the exact same spot on several pieces.
 
Top