Who's loading a Warbird

Allen Vinyard

Member
Joined
May 3, 2001
Messages
15
Location
Levelland, TX
Who\'s loading a Warbird

I haven't started loading for mine yet but I wonder if anyone is.
What are you using?
I plan to use a 200 Nosler partition for starters, RL25, H1000 or ????
Suggestions...
Results...

Thanks
Allen
 
Re: Who\'s loading a Warbird

I had one some time back in a Lilja barreled rig , I abandoned the project due to the cost of the brass and the false velocities stated by Lazz.
But I think that I got best results from R-25 and IMR-7828

Best of luck with yours
 
Re: Who\'s loading a Warbird

I have been shooting them for about 4 years and have some different loads I played around with. some shot out of a sako TRGS and some shot out of one of a Lazzeroni built rifle.

Loads shot out of the Lazzeroni rifle. 27 inch barrell

150 gr barns X coated from lazzeroni AOL 3.60
100 gr RL 25 3453 Average
103 gr RL 25 3541
106 gr RL 25 3670
107 gr Rl 25 3682
108 gr RL 25 3713
109 gr RL 25 3796

150 gr barns X coated from lazzeroni AOL 3.60

103.5 Gr IMR 7828 3729


180 grain Noseler Partition Coated from Lazzeroni

96 gr RL 25 3300
100 gr Rl 25 3345
102 gr Rl 25 3421
104 gr Rl 25 3459

165 Noseler BT
106.5 RL 25 3696
100.5 IMR 7828 3535

165 Grain Barns XLC
106.5 Gr Rl 25 3591
100.5 Gr IMR 7828 3429

150 Grain Swift Scricco
103.5 GR IMR 7828 3649

The best load I found For the TRGS

165 Scricco
106.5 GR RL 25 3592

I hope this helps!
 
Re: Who\'s loading a Warbird

Thanks guys.
I don't come here real often, I've got a lot on my plate right now but
for those who don't remember me or were not here when I started this project, this rifle is a
Ruger# 1 stainless that I spent a lot of money on.
Of all the things that have been done to it, the most important is the fact that it has a 28 1/2 inch
fluted stainless match barrel. PACNOR I believe. I can't believe I have forgotten what all I did to the rifle.
I've had the rifle now probably 3 years and have not fired it.
The dies, as far as I know can only be obtained from Lazeroni, at least if I want RCBS.
They are $200 for a full length set.
Brass is very expensive.
Some times I wish I had picked one of the other "super' 30's
I'm hoping to get goin on it this spring tho'.
Sure am itching to see what it will do.
I asked about powders because I have heard of some pressure issues with RL25.
 
Re: Who\'s loading a Warbird

Allen
You can get data from Lazzeroni's web site. You should defintely start low and work up. The MAX load pressures are too high in my rifle. And in a TRGS that I loaded for they would have been plain scary. But I do hit the 3500 mark with a 180 Accubond using RL25 (27"). That TGRS (26") burning 7828 and pushing 180 Accubonds, would do 3425 (IIRC) and did it at 4 grains below MAX.
 
Re: Who\'s loading a Warbird

I think the dies are around $109 and you can order the brass from midway for $40 per box.

Most of the Pressures you here of are people trying to get the stated velocities from 25 or 26 barels.

I did not have any problems getting the stated velocities out of my rifle until receantly. My throat is gone, I need a new barrel.

I shot the 130 grain barns 4014 fps. That is smokin out of a 30 cal.

Good luck
 
Warning! This thread is more than 20 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top