Measuring Scope Height with a 20MOA Rail ??

.25MOA

Well-Known Member
Joined
Jan 16, 2010
Messages
81
Location
Sydney Australia
Hi Guys,,,yes it's probably been asked before but i cant find a clear answer ?? Is it possible to do ?? where do we measure from ?? I have measured from firing pin to centre of the scope mounts.....as the rail is higher at the rear, is it better to measure at the objective ???

Cheers, Ray.....
 
Ive always measured scope tube and bolt diameter, and distance form bolt to scope. Take half the tube half the bolt and add them numbers to distance between tube and bolt. Always work great for me out past a thousand.
 
I measure center of the bolt to center of the tube at the center of the elevation knob. In my pea brain and limited knowledge of the modern rifle scope that is the place that makes the most sense to me.

Someone with a more working knowledge of a rifle scope should chime in as to whether it makes a difference as to where in the elevation scheme your zero lies. I use a 10MOA base and where the scope is zeroed leaves about 45MOA up so it is zeroed off center. Does that make a difference?

In my setup a 1/8 inch difference 1.75" verses 1.875" equals a .5 MOA difference in Exbal at 800 yards. Measuring at the center of the elevation turret very carefully has worked OK for me as far as I can tell and that adjustment is 1.875".

On another note that is another adjustment one can make when proving a drop chart and trying to make all points of impact agree with the generated chart especially farther out even though I have not done that....food for thought.
 
tell me if this is wrong, i measure the scope objective bell/ by 2, then measure the diameter of the barrel directly below that and / by 2 then add those two numbers to the distance between the bell and barrel rite?
 
tell me if this is wrong, i measure the scope objective bell/ by 2, then measure the diameter of the barrel directly below that and / by 2 then add those two numbers to the distance between the bell and barrel rite?


Close. A 20 moa cantered rail would be a little off, thus I use...

Formula= (Scope's "Tube Diameter"\2) + (Bolt's "Diameter"\2) + (Distance between bottom of scope tube and top of bolt in middle of tube area equally between ring mounts) = Scope Height!

Just as C.O.Shooter posted!

http://www.accurateshooter.com/optics/determining-scope-height-above-bore/
 
My best guess would be that the optically correct location to measure the height to would be the center of the exit pupil (if you can find it).
 
there comes a point where its best to accept easy answers unfair as that may seem at times. which is another way of saying just go shoot the freakin thing.


Well said!

Out of curiosity, I just ran the data, on Exbal, for one of my rifles at 1000 yds. The elevation at that distance came back as 28.25 MOA. I then went back and only changed the scope height from 1.75" to 2.0". That elevation came back as 28.0 MOA.

1/4 MOA change at 1000 for a 1/4" difference in scope height.

I just wish I had a place to shoot at 1000 to demonstrate it!


Pete
 
As previously mentioned, measuring & adjusting to fit dope seems to work the best for me. I measure at the turrets, then tweak it to fit actual poi at range
 
Hi Guys,,,yes it's probably been asked before but i cant find a clear answer ?? Is it possible to do ?? where do we measure from ?? I have measured from firing pin to centre of the scope mounts.....as the rail is higher at the rear, is it better to measure at the objective ???

Cheers, Ray.....
It makes no practical difference. When you input 1.8 or 2.0 inches above bore, for example, to any ballistics calculator your elevation data does not change out to 1500 yards at least. Most low rings are 1.5, mediums 1.75 highs 2.0 extra high 2.25 for the purpose of getting accurate info from a ballistic calculator. Most calculators will even round yo 1.75 to 1.8. It does not need to be more precise than that.
 

Recent Posts

Top