Hornady .257" 134 ELD-M
- Thread starter lancetkenyon
- Start date
Help Support Long Range Hunting Forum
I haven't found THE load yet, still shooting the handloads from the previous owner. They are going 3230fps with H1000. Sent the barrel back to TS Customs to have the chamber opened up to their specd reamer, similar to the AW2 reamer.
willfrye027
Well-Known Member
Just did a rough pressure ladder. PLEASE don't duplicate without working up in your own rifle.
I wanted to see how the eldm would compare to my well established Berger 135 load
25 creedmoor tikka action 26" PBB prefit 1:7 twist. Has about 800 rounds on the barrel.
Current load is 43.2gr N555 in lapua SRP with CCI #41 going 2920fps
I pulled 5 of these loads to run a pressure ladder with the new ELDs.
Had to turn my seating die to seat these deeper, they are longer than the Berger's. They are just kissing the lands. Again just roughing it in to get an idea. Have a fresh prefit ready to spin on when I burn this barrel out.
N555
40gr. 2665
41gr 2775
42gr 2863
43gr 2923
44gr 2991 ***slight ejector mark and a hint of heavier bolt lift here
Probably will run in the 43-44 range. Lowest two holes on the target are 43 and 44.
Almost identical to my 135gr Berger pressure ladder. This is with my magneto speed hanging off the end. I have no doubt they will group well with this combo.
I wanted to see how the eldm would compare to my well established Berger 135 load
25 creedmoor tikka action 26" PBB prefit 1:7 twist. Has about 800 rounds on the barrel.
Current load is 43.2gr N555 in lapua SRP with CCI #41 going 2920fps
I pulled 5 of these loads to run a pressure ladder with the new ELDs.
Had to turn my seating die to seat these deeper, they are longer than the Berger's. They are just kissing the lands. Again just roughing it in to get an idea. Have a fresh prefit ready to spin on when I burn this barrel out.
N555
40gr. 2665
41gr 2775
42gr 2863
43gr 2923
44gr 2991 ***slight ejector mark and a hint of heavier bolt lift here
Probably will run in the 43-44 range. Lowest two holes on the target are 43 and 44.
Almost identical to my 135gr Berger pressure ladder. This is with my magneto speed hanging off the end. I have no doubt they will group well with this combo.
Graf has them in stock again
www.grafs.com
HORNADY 25c (.257) 134gr ELD MATCH 100/BX - Graf & Sons
25 Cal .257 134 gr ELD® Match ELD® Match (Extremely Low Drag Match) bullets are technologically advanced, enhanced accuracy target bullets featuring Heat Shield® tips with the PERFECT MEPLAT (tip point) combined with numerous design features that deliver the highest-in-class ballistic...
www.grafs.com
Bud LaRoche
Well-Known Member
What brass you using? I've got a 25PRC in the assembly line currently. Exciting
George building it? I'm almost ready to pull the trigger on one as well.
Bud LaRoche
Well-Known Member
Yup , it's at GAP Headquarters now . My Tempest action was naked for to long.
Gobbler256
Well-Known Member
Can you tell what " them " are??
Sweet, I need to get a 25 build going with him too. just can't decide between PRC or SAUM.
Bud LaRoche
Well-Known Member
Tuff choice.
I chose PRC because I already have a 6.5GAP4's and I don't want to share it's brass , lol. Hopefully I can get some matches in with the new PRC as well. I went with a 1.25 tube
I chose PRC because I already have a 6.5GAP4's and I don't want to share it's brass , lol. Hopefully I can get some matches in with the new PRC as well. I went with a 1.25 tube
I'm still working with my old RP300SAUM brass necked down but bought some ADG 6.5SAUM brass so leaning that way. No clickers....
May be my best group ever. 25 prc at 500 yards with a 135 berger.
Phil Rizzo
Well-Known Member
Anybody seeing much difference in the 133 EH and the 135 LRHT?
My gun seems exceptionally finicky with the 133 out to 300.
Havent made it further than that yet.
3150-3200fps
Awesome job Sykes!
My gun seems exceptionally finicky with the 133 out to 300.
Havent made it further than that yet.
3150-3200fps
Awesome job Sykes!
