montana_native
Well-Known Member
Model 700 RR Prefix Action
- Single shot plate fitted to magazine well and spot-tigged into place
- PTG Oversized 1-piece bolt to fit trued-up raceway
- M16 Extractor
- 8-40 rail screws
- Nightforce steel base 20 MOA
- Standard Timney Trigger
Manners EH1
- began life as a short action single shot
- recoil lug relief for LA was added and the SA filled with Devcon
- SA action screw/pillar relief was filled with Devcon
- pillar bedded
- barrel channel is for a Proof Sendero
- ADL trigger guard
- 4" Pic rail
Barrel
- Bartlein Sendero Contour
- 28"
- 10-twist
- MBM Beast brake
- "Do your part 3000" was engraved on the top of the barrel as a parody/inside joke
- Small rub mark from user error in scope ring selection
- 82 rounds
Fireform Barrel
- 30 cal 10-twist Rem 700 Sendero contour take-off barrel that was brand new
- 25" length with a Cooley brake
- 105 rounds
All metal was Cerakoted with a Tungsten/Black mix.
Also included
- 90 pieces of 2x fired brass (private headstamp 338 Lapua RWS brass)
- Custom Hornady Sizing Die
- Forster Bench-rest seater die
All metal work was done by Dave Young of Young's Gunsmithing in Sand Coulee, MT.
The rifle as pictured weighs 12.7#. It proved to be very accurate with 215 Hybrid Bergers at 3192 fps and Retumbo. RL 33 netted about 60 fps more velocity but wasn't quite as accurate and there was noticeably more muzzle blast.
I haven't shot the rifle in over a year and have lost interest...as I do with most rifle projects.
I'd like to have $1500 shipped to your FFL for everything listed (scope, rings not included). No trades.
- Single shot plate fitted to magazine well and spot-tigged into place
- PTG Oversized 1-piece bolt to fit trued-up raceway
- M16 Extractor
- 8-40 rail screws
- Nightforce steel base 20 MOA
- Standard Timney Trigger
Manners EH1
- began life as a short action single shot
- recoil lug relief for LA was added and the SA filled with Devcon
- SA action screw/pillar relief was filled with Devcon
- pillar bedded
- barrel channel is for a Proof Sendero
- ADL trigger guard
- 4" Pic rail
Barrel
- Bartlein Sendero Contour
- 28"
- 10-twist
- MBM Beast brake
- "Do your part 3000" was engraved on the top of the barrel as a parody/inside joke
- Small rub mark from user error in scope ring selection
- 82 rounds
Fireform Barrel
- 30 cal 10-twist Rem 700 Sendero contour take-off barrel that was brand new
- 25" length with a Cooley brake
- 105 rounds
All metal was Cerakoted with a Tungsten/Black mix.
Also included
- 90 pieces of 2x fired brass (private headstamp 338 Lapua RWS brass)
- Custom Hornady Sizing Die
- Forster Bench-rest seater die
All metal work was done by Dave Young of Young's Gunsmithing in Sand Coulee, MT.
The rifle as pictured weighs 12.7#. It proved to be very accurate with 215 Hybrid Bergers at 3192 fps and Retumbo. RL 33 netted about 60 fps more velocity but wasn't quite as accurate and there was noticeably more muzzle blast.
I haven't shot the rifle in over a year and have lost interest...as I do with most rifle projects.
I'd like to have $1500 shipped to your FFL for everything listed (scope, rings not included). No trades.
Last edited: