What's your favorite dies for the 284. And what types do you typically use. Stepping up from the 260 to the 284 and would like you expertise. Thanks
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
284 Winchester dies
- Thread starter vern.284
- Start date
Help Support Long Range Hunting Forum
This is a tough question. Depends on your chamber is it SAMMI or custom? Are you target shooting or hunting?
I use Redding for my 284 which has its necks turned per the specs of my custom reamer. I use a bushing die, body bump die and a competition seating die.
With Redding you can go several ways: with a basic FL (full length) die and a seater die, a FL/bushing die and a competition seating die, or a three die set which separates the neck sizing and body sizing into two dies plus a competition seater die (like I did).
There are a few other variations from Redding. Some of the sets are outrageously expensive. There is one that uses a competition style die (with micrometer top) for the bushing AND the Seating plus a body die. Approx $450!!!
Basic two die sets (FL/ Seater) are available from RCBS, Hornady or others. These can size your brass just fine and save you a ton of money and effort. I still use these types of die sets for many of my hunting rifles.
I use Redding for my 284 which has its necks turned per the specs of my custom reamer. I use a bushing die, body bump die and a competition seating die.
With Redding you can go several ways: with a basic FL (full length) die and a seater die, a FL/bushing die and a competition seating die, or a three die set which separates the neck sizing and body sizing into two dies plus a competition seater die (like I did).
There are a few other variations from Redding. Some of the sets are outrageously expensive. There is one that uses a competition style die (with micrometer top) for the bushing AND the Seating plus a body die. Approx $450!!!
Basic two die sets (FL/ Seater) are available from RCBS, Hornady or others. These can size your brass just fine and save you a ton of money and effort. I still use these types of die sets for many of my hunting rifles.
Seabeeken
Well-Known Member
I use both Forster FL and Wilson bushing dies.
I had some issues with Redding. A FL die non bushing die induced .010 neck runout and also found holes not centered in several of my Redding bushings. The redding dies that I do use are equipped with Wilson bushings now
I had some issues with Redding. A FL die non bushing die induced .010 neck runout and also found holes not centered in several of my Redding bushings. The redding dies that I do use are equipped with Wilson bushings now
So this will be for a hunting / target rifle. I'd like to keep it simple at SAAMI chamber nothing custom right now.
I guess I should have been more specific on 2 or 3 die sets. And which one you use for yourself. Both make and your preference on dies
I guess I should have been more specific on 2 or 3 die sets. And which one you use for yourself. Both make and your preference on dies
I get good runout with my Redding bushing sizer.
I load for hunting and long range target shooting and the bushings allow me to adjust neck tension for either.
However, I do use a Wilson seater for my target ammo and it may help improve bullet runout due to its mechanical design.
FWIW, my Wilson #4 26" hunting rifle shoots about as accurately as my 30" MTU target rifle.
I load for hunting and long range target shooting and the bushings allow me to adjust neck tension for either.
However, I do use a Wilson seater for my target ammo and it may help improve bullet runout due to its mechanical design.
FWIW, my Wilson #4 26" hunting rifle shoots about as accurately as my 30" MTU target rifle.
got a basic forster set if youre looking
www.longrangehunting.com
Forster and RCBS dies
got these in a lot so know nothing about their life but they did have some surface rust and general gunk. so they were soaked in evapo rust and they look and function like new. 222 rem - forster br dies . the neck sizer alum collar is binding about haflway up (verified using a different...
Those may work fine if the neck hasn't been custom reamed for someone who neck-turns brass.got a basic forster set if youre looking
Forster and RCBS dies
got these in a lot so know nothing about their life but they did have some surface rust and general gunk. so they were soaked in evapo rust and they look and function like new. 222 rem - forster br dies . the neck sizer alum collar is binding about haflway up (verified using a different...
