FARRELL 30MM RINGS, Low List $166 sell for $90 shipped
Farrell Rings are precision CNC machined from a single piece of solid steel or aluminum. They are a Picatinny system that will mate with any 1913 Mil Spec Picatinny Mount. When used with the Farrell Scope base, it is our goal to have a center line with less than .001 inch deviation. Most rings are made in either aluminum or steel. With a black matte finish. They are made in five different heights in both 1 inch and 30MM. The new design of Farrell rings are grooved on the inside of the diameter to reduce weight and improve clamping, We recommend to not use loctite with our taper head screws as they utilize a 360 degree mating surface.
The Farrell clamp to the rail, we believe is second to none. The ring cross bolt is located concentric across the dovetail angles and pulls the ring down and over to the centerline of the base, creating an even pressure. This enables the torque to be applied in such a way as to prevent stressing and moving the center line of the ring.
The clamp is designed to pivot on all surfaces to assure proper contact on the rail, the ring and the cross bolt. This is accomplished by using a radius on all points of contact. This is very important, especially when different manufacturers of rails might have different dimensions across the 45 degree angles that all rings mount on (picatinny or weaver style).
RING HEIGHTS - 1" and 30mm ( From the Top of the base to the centerline of the tube. )
LOW = 0.735"
STANDARD = 0.835"
MEDIUM = 0.935"
HIGH = 1.035"
EX-HIGH = 1.235"
50 in/lbs of torque is used on our cross bolt.
There are four screw caps. Use 15 to 20 Inch lbs.
Farrell Base for a Nosler M48 Long 20 MOA - List $118 sell for $50 plus shipping.
All of our products are machined from solid stock, nothing we build is outsourced. That is how we maintain quality.
Each set of scope rings are engraved with serial numbers and matched as they are machined.
All steel products are finished with black matte oxide, custom stainless rails have a bead blasted matte finish.
It is our goal to provide tolerances to .001 or less and great care is taken to provide the best fitting mount you will ever own.
Each product comes with the necessary screws and instructions.
Our screws are produced in the U.S. to our specifications, undergoing heat treating with a 45 degree head that seats against a 45 degree counterbore to ensure your rail centers to the receiver.
Rifle scope mounts are true 1913 picatinny specs.
MOUNTING FARRELL SCOPE BASES AND RINGS- If they are mounted properly and without any stress there should be no reason to lap our rings upon installation. For those who wish to mount and maintain this flatness, we've provided a bedding groove (a first) on the underside of the mount to allow a dense application of epoxy. It is common, but not always necessary for rifle receivers with steps such as Remington 700, Mauser 98, Pre-64 Winchester etc., to possibly need bedding material on the rear where they have been polished or ground excessively. Round top style receivers rarely will need any bedding.
1" tube, .76", 4 cap screw
+ COMPARE
1" TUBE, .76", 4 CAP SCREW
Scopes are only as good as the rings they are mounted in. Seekins Precision Scope Rings are the best available through superior design, precision machining and obsessive attention to detail. Built to the 1913 Picatinny Specification from 7075-T6 aluminum, these Seekins scope rings are available in .76" height to accommodate most rifle and optic combinations.
Perfectly CNC Machined 7075-T6 Billet
1913 Picatinny Mil-Spec
Type III Class 2 Hardcoat Anodized Finish
Center lug machined into place
Grade 8 T25 Torx Screws
Serialized Pairs
Slim Line Clamps
SEEKINS 1" Rings List $119 sell $50 plus shipping
1" TUBE, .76", 4 CAP SCREW
Scopes are only as good as the rings they are mounted in. Seekins Precision Scope Rings are the best available through superior design, precision machining and obsessive attention to detail. Built to the 1913 Picatinny Specification from 7075-T6 aluminum, these Seekins scope rings are available in .76" height to accommodate most rifle and optic combinations.
Perfectly CNC Machined 7075-T6 Billet
1913 Picatinny Mil-Spec
Type III Class 2 Hardcoat Anodized Finish
Center lug machined into place
Grade 8 T25 Torx Screws
Serialized Pairs
Slim Line Clamps
Farrell Rings are precision CNC machined from a single piece of solid steel or aluminum. They are a Picatinny system that will mate with any 1913 Mil Spec Picatinny Mount. When used with the Farrell Scope base, it is our goal to have a center line with less than .001 inch deviation. Most rings are made in either aluminum or steel. With a black matte finish. They are made in five different heights in both 1 inch and 30MM. The new design of Farrell rings are grooved on the inside of the diameter to reduce weight and improve clamping, We recommend to not use loctite with our taper head screws as they utilize a 360 degree mating surface.
The Farrell clamp to the rail, we believe is second to none. The ring cross bolt is located concentric across the dovetail angles and pulls the ring down and over to the centerline of the base, creating an even pressure. This enables the torque to be applied in such a way as to prevent stressing and moving the center line of the ring.
The clamp is designed to pivot on all surfaces to assure proper contact on the rail, the ring and the cross bolt. This is accomplished by using a radius on all points of contact. This is very important, especially when different manufacturers of rails might have different dimensions across the 45 degree angles that all rings mount on (picatinny or weaver style).
RING HEIGHTS - 1" and 30mm ( From the Top of the base to the centerline of the tube. )
LOW = 0.735"
STANDARD = 0.835"
MEDIUM = 0.935"
HIGH = 1.035"
EX-HIGH = 1.235"
50 in/lbs of torque is used on our cross bolt.
There are four screw caps. Use 15 to 20 Inch lbs.
Farrell Base for a Nosler M48 Long 20 MOA - List $118 sell for $50 plus shipping.
All of our products are machined from solid stock, nothing we build is outsourced. That is how we maintain quality.
Each set of scope rings are engraved with serial numbers and matched as they are machined.
All steel products are finished with black matte oxide, custom stainless rails have a bead blasted matte finish.
It is our goal to provide tolerances to .001 or less and great care is taken to provide the best fitting mount you will ever own.
Each product comes with the necessary screws and instructions.
Our screws are produced in the U.S. to our specifications, undergoing heat treating with a 45 degree head that seats against a 45 degree counterbore to ensure your rail centers to the receiver.
Rifle scope mounts are true 1913 picatinny specs.
MOUNTING FARRELL SCOPE BASES AND RINGS- If they are mounted properly and without any stress there should be no reason to lap our rings upon installation. For those who wish to mount and maintain this flatness, we've provided a bedding groove (a first) on the underside of the mount to allow a dense application of epoxy. It is common, but not always necessary for rifle receivers with steps such as Remington 700, Mauser 98, Pre-64 Winchester etc., to possibly need bedding material on the rear where they have been polished or ground excessively. Round top style receivers rarely will need any bedding.
1" tube, .76", 4 cap screw
+ COMPARE
1" TUBE, .76", 4 CAP SCREW
Scopes are only as good as the rings they are mounted in. Seekins Precision Scope Rings are the best available through superior design, precision machining and obsessive attention to detail. Built to the 1913 Picatinny Specification from 7075-T6 aluminum, these Seekins scope rings are available in .76" height to accommodate most rifle and optic combinations.
Perfectly CNC Machined 7075-T6 Billet
1913 Picatinny Mil-Spec
Type III Class 2 Hardcoat Anodized Finish
Center lug machined into place
Grade 8 T25 Torx Screws
Serialized Pairs
Slim Line Clamps
SEEKINS 1" Rings List $119 sell $50 plus shipping
1" TUBE, .76", 4 CAP SCREW
Scopes are only as good as the rings they are mounted in. Seekins Precision Scope Rings are the best available through superior design, precision machining and obsessive attention to detail. Built to the 1913 Picatinny Specification from 7075-T6 aluminum, these Seekins scope rings are available in .76" height to accommodate most rifle and optic combinations.
Perfectly CNC Machined 7075-T6 Billet
1913 Picatinny Mil-Spec
Type III Class 2 Hardcoat Anodized Finish
Center lug machined into place
Grade 8 T25 Torx Screws
Serialized Pairs
Slim Line Clamps
