Quickload

[philsummers21]

So found out about this program quickload. Seems pretty **** useful. Any thoughts? I'm loading up my 22-250 and I'm curious if I can work up to a next accuracy node or not since my COAL is quite a bit longer then Sami spec. Current COAL is 2.510. 64gr Berger using IMR 4350. Case length 1.910. 45.5 grains of water. 26" barrel
Can anyone run this for me.

 

[AD5GB]

Well, not a great rendering of tabular data but you may be able to line it up....


+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Cartridge : .22-250 Rem. (SAAMI)
Bullet : .224, 64, Berger M Var #22316
Useable Case Capaci: 43.338 grain H2O = 2.814 cm�
Cartridge O.A.L. L6: 2.510 inch = 63.75 mm
Barrel Length : 26.0 inch = 660.4 mm
Powder : IMR 4350

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 83 32.80 2892 1189 32214 8090 87.3 1.387
-18.0 85 33.62 2962 1247 34413 8349 88.7 1.350
-16.0 87 34.44 3033 1307 36761 8601 90.0 1.315
-14.0 89 35.26 3103 1369 39271 8846 91.2 1.276
-12.0 91 36.08 3174 1432 41954 9081 92.4 1.238
-10.0 93 36.90 3245 1496 44810 9306 93.4 1.201
-08.0 95 37.72 3315 1562 47835 9521 94.5 1.166
-06.0 97 38.54 3386 1629 51061 9723 95.4 1.132
-04.0 99 39.36 3456 1698 54509 9913 96.2 1.100
-02.0 101 40.18 3526 1767 58197 10089 97.0 1.068 ! Near Maximum !
+00.0 103 41.00 3596 1838 62142 10250 97.7 1.038 ! Near Maximum !
+02.0 105 41.82 3666 1910 66373 10396 98.3 1.008 !DANGEROUS LOAD-DO NOT USE!
+04.0 107 42.64 3736 1983 70907 10526 98.8 0.980 !DANGEROUS LOAD-DO NOT USE!
+06.0 109 43.46 3805 2057 75775 10638 99.2 0.952 !DANGEROUS LOAD-DO NOT USE!
+08.0 111 44.28 3874 2132 81006 10732 99.6 0.926 !DANGEROUS LOAD-DO NOT USE!
+10.0 114 45.10 3942 2208 86636 10808 99.8 0.900 !DANGEROUS LOAD-DO NOT USE!

Results caused by � 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 103 41.00 3756 2005 73231 10134 100.0 0.967 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 103 41.00 3385 1628 51258 9896 91.7 1.130

 

[philsummers21]

Awesome thank you. I will have to purchase that program.

 

[AD5GB]

Awesome thank you. I will have to purchase that program.

HaH! Yeah I've only had it a couple weeks so I'm still learning about it but it's been a great tool so far. Worth every penny and then some! It doesn't have the latest IMR Enduron line of powders though. At least not yet. Hoping they're coming...

 

[philsummers21]

Looks like I can push it up another node or 2. I'm chroning a bit faster

 

[AD5GB]

Looks like I can push it up another node or 2. I'm chroning a bit faster but could be my elevation

Some of my WinMag loads chrono higher as well. I have a Brux cut rifled barrel though so I'd attributed it to that. Nonetheless, it's a great tool!

 

[benchracer]

So found out about this program quickload. Seems pretty **** useful. Any thoughts? I'm loading up my 22-250 and I'm curious if I can work up to a next accuracy node or not since my COAL is quite a bit longer then Sami spec. Current COAL is 2.510. 64gr Berger using IMR 4350. Case length 1.910. 45.5 grains of water. 26" barrel
Can anyone run this for me.

With the data you provided, the high node will show up around 3450.

 

[philsummers21]

With the data you provided, the high node will show up around 3450.

Now where do you see that? All I see are numbers. Would love to be able to pick out possible nodes. And right now my load is 37 grains imr 4350 at 3350fps. Shoots well just hoping I can get a little more speed. My other load is a 53 vmax at 3700, just trying out these heavier bergers to see what they can do

[/URL][/IMG]

 

[benchracer]

Where do I see that? On my own copy of QL, using barrel time data.

The following thread may help to explain things:

http://www.longrangehunting.com/forums/f28/how-far-apart-nodes-140877/

 

[benchracer]

BTW, assuming the same OAL, the high node with the 53 VMAX is around 3830 or so.

 

[philsummers21]

Where do I see that? On my own copy of QL, using barrel time data.

The following thread may help to explain things:

http://www.longrangehunting.com/forums/f28/how-far-apart-nodes-140877/

Ah. I wasn't being a smart *** either by the way. I hope I didn't come across that way. Wow. 3800 with that 53. That's going to be hard to beat. Even at 3700 I can't really see any gains with the 64 @3500

 

[philsummers21]

And yeah that 53 comes in at the exact same COAL. I found that interesting when I did the seating depth tests on the berger

 

[benchracer]

No worries. Your case volume and chamber dimensions appear to be nearly identical to mine. In my rifle, the OAL to the lands was nearly identical for the 53 VMAX and 69 SMK.

The 53 VMAX is hard to beat.

 

[philsummers21]

Yeah I like the vmax. They just don't quite fly as well as the bergers. Maybe I should try a different powder with them. Currently using 36.3 of Varget