Crowe284
Well-Known Member
I bought this rifle here In October of 2016. This rifle is an absolute hammer. My current load is fairly mild to preserve brass life. I'm shooting a 143 ELDX over 60 gr of H1000 @ 3033 fps in Remington 300 saum brass. Five cold bore shots yielded an ES of 7 fps with an SD of 2.6 fps. This load consistently shoots mid .1's to low .2's. Barrel had 422 rounds on it when purchased and I have put another 166 rounds through the rifle for a total 588 so lots of life left. The rifle had been used to hunt so it has a couple minor marks here and there but you have to look for them. There is a bit of the typical brass rash on Cerekote behind ejection port but again not bad at all. Here are the specs on the rifle:
Complete rifle built by GA Precision
-Templar V1 left hand action (Defiance)
-Will include 20 MOA rail that is Cerekoted to match barreled action and a set of 30 mm Talley one piece lightweight base/rings
-Triggertech trigger
-Manners MCS-T Elite, 2 flush cups right side, sling stud front and rear, GAP Flectern camo by Custom Gun Coatings, flawless bedding job by GA Precision
-24" Bartlein #3 fluted, 8.7 twist, Vías Muzzle brake
-Badger Ordnance M5 DBM
-3 Mags included
-All metal Cerekoted in mil-spec OD green
Also included with sale will be all of the 300 saum brass that I have for the rifle (more than 100 pieces, would have to count to know for sure) and 50 pieces of latest generation hornady brass unfired. The rifle will ship in a hard case to your ffl. Your ffl must accept shipment from an individual. Shipping and insurance is included in the price. I have attached a couple photos of rifle that previous owner had. Will upload more photos this afternoon or tomorrow. Thanks for looking and if you have any questions you can reach me quickest via text @ 210 two six two 7416.
Cost to build rifle new from GAP 4,585.00
Asking 2,900 shipped and insured in hard case from me to your FFL.
Complete rifle built by GA Precision
-Templar V1 left hand action (Defiance)
-Will include 20 MOA rail that is Cerekoted to match barreled action and a set of 30 mm Talley one piece lightweight base/rings
-Triggertech trigger
-Manners MCS-T Elite, 2 flush cups right side, sling stud front and rear, GAP Flectern camo by Custom Gun Coatings, flawless bedding job by GA Precision
-24" Bartlein #3 fluted, 8.7 twist, Vías Muzzle brake
-Badger Ordnance M5 DBM
-3 Mags included
-All metal Cerekoted in mil-spec OD green
Also included with sale will be all of the 300 saum brass that I have for the rifle (more than 100 pieces, would have to count to know for sure) and 50 pieces of latest generation hornady brass unfired. The rifle will ship in a hard case to your ffl. Your ffl must accept shipment from an individual. Shipping and insurance is included in the price. I have attached a couple photos of rifle that previous owner had. Will upload more photos this afternoon or tomorrow. Thanks for looking and if you have any questions you can reach me quickest via text @ 210 two six two 7416.
Cost to build rifle new from GAP 4,585.00
Asking 2,900 shipped and insured in hard case from me to your FFL.
Attachments
-
DF24FB6C-A072-4E0D-A9BA-29A5BE161109.jpeg9.3 KB · Views: 171
-
034A447E-0954-499A-BFDA-DBB26FA7BE0E.jpeg162.7 KB · Views: 146
-
61DC3A4F-7D60-495A-AD0F-C8AD0AEFCA0E.jpeg1.3 MB · Views: 158
-
7A442E0D-997B-43F1-90DC-CEACF929B19B.jpeg1.4 MB · Views: 141
-
11CABA87-06E8-49F2-9A0F-70955327A4D6.jpeg1.2 MB · Views: 135
-
2FF6F5BC-D2E1-463D-867C-DF3FB33E7940.jpeg1.2 MB · Views: 154
Last edited: