Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Bedding a Christensen Arms Mesa
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="MallardAddict" data-source="post: 1840880" data-attributes="member: 3830"><p>I almost always bed my actions and typically the chamber area of the barrel, particularly on heavy barrels (I know CA isn't heavy) to ensure the barrel isn't torquing the action.</p><p></p><p>Easy enough to check action bedding/float issues. Pull the action out of the stock and see if there is uneven paint wear in the action area to indicate movement under recoil. If there is then atleast bed the action.</p><p></p><p>As a test for the barrel channel/float, put a layer or 2 of 3m 20mm pipe wrap tape in the barrel channel under the chamber area , just enough to get a slight bit of tension/support under the chamber. Bolt it back together and shoot it, if it gets better you have your answer, bed the chamber area and rock on.</p><p></p><p>Never played with a CA stock but i have had some flimsy factory stocks. What I did was since I was going to be bedding action and likely the chamber area anyways I used my trim router to make a small slot about 1/2" wide and 3/8" deep down the entire barrel channel from about 2" in front of the recoil lug to about 2" from the end of the forend. I then bedded in a 2 pieces of carbon archery arrow (stiff and light) side by side the length of the slot. Once the epoxy dried I used a deep well socket and sandpaper to shape the excess epoxy to the original barrel channel shape and painted the barrel channel. This addition was invisible and stiffened the forend immensely while only adding a few ounces of weight.</p></blockquote><p></p>
[QUOTE="MallardAddict, post: 1840880, member: 3830"] I almost always bed my actions and typically the chamber area of the barrel, particularly on heavy barrels (I know CA isn’t heavy) to ensure the barrel isn’t torquing the action. Easy enough to check action bedding/float issues. Pull the action out of the stock and see if there is uneven paint wear in the action area to indicate movement under recoil. If there is then atleast bed the action. As a test for the barrel channel/float, put a layer or 2 of 3m 20mm pipe wrap tape in the barrel channel under the chamber area , just enough to get a slight bit of tension/support under the chamber. Bolt it back together and shoot it, if it gets better you have your answer, bed the chamber area and rock on. Never played with a CA stock but i have had some flimsy factory stocks. What I did was since I was going to be bedding action and likely the chamber area anyways I used my trim router to make a small slot about 1/2“ wide and 3/8” deep down the entire barrel channel from about 2” in front of the recoil lug to about 2” from the end of the forend. I then bedded in a 2 pieces of carbon archery arrow (stiff and light) side by side the length of the slot. Once the epoxy dried I used a deep well socket and sandpaper to shape the excess epoxy to the original barrel channel shape and painted the barrel channel. This addition was invisible and stiffened the forend immensely while only adding a few ounces of weight. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Bedding a Christensen Arms Mesa
Top