Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Savage 111 LRH 338 Lapua
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Texas Republic" data-source="post: 716023" data-attributes="member: 19878"><p>In case you dont recall, I have had issues with hornady brass becoming stuck inside my chamber after firing and even a very stiff bolt with lapua brass. It seems a lot of people have been having the same issue. Once I had separation occur of the brass from the lower primer portion, I decided I was done shooting the rifle until the issue was resolved. Separation is when the fired brass splits into two pieces inside the chamber. Its hard to explain. Basically, after I fired a round ....I pulled the bolt back to reveal TWO pieces of brass. </p><p></p><p> Its been a while since I posted on the subject because I wanted to get to the bottom of this before I said anything. The rifle's accuracy is not something I can complain about. It seems to shoot fine, but is a nightmare when it comes to ejecting brass, etc. </p><p></p><p>My friend who taught me a lot about shooting still has many friends that he met throughout scout sniper school. One of those is a gunsmith who builts custom rifles. After I showed my friend the problems I was having with my LRH111, he wanted to take it to the gunsmith he knows.</p><p></p><p>The gunsmith that he sent my rifle off to did some basic tests first to see if it was a head-spacing issue. After looking at some of my fired brass he was afraid the rifle might be over chambered. So he sent it off to his friend to have it air mikd on his own equipment. </p><p></p><p>Anyhow, I was told the following: </p><p>(I may not be repeating it correctly so bear with me)</p><p></p><p>The gun smith said the air miked results show that is it over chambered in shoulder length by .003 (three-thousandths) of an inch. This is making the brass slap up against the chamber when fired and stretching the brass much more than normal. No wonder I was trimming it all the freaking time. The tests ALSO show that it is "out of round" inside the chamber. So bad news on two major issues. </p><p></p><p>There is no way the gunsmith can fix anything like that obviously, so it is fixing to go back to Savage. The gunsmith supposedly has contacts at Savage and is going to call them up to explain the situation and provide all the results that I need. I dont see how they can "fix" an issue like that without replacing the entire chamber. I have not even fired over 200 rounds through the barrel so its pretty new. </p><p></p><p>I will follow up with another post once I hear back from Savage. I plan on mailing it to them sometime next week.</p></blockquote><p></p>
[QUOTE="Texas Republic, post: 716023, member: 19878"] In case you dont recall, I have had issues with hornady brass becoming stuck inside my chamber after firing and even a very stiff bolt with lapua brass. It seems a lot of people have been having the same issue. Once I had separation occur of the brass from the lower primer portion, I decided I was done shooting the rifle until the issue was resolved. Separation is when the fired brass splits into two pieces inside the chamber. Its hard to explain. Basically, after I fired a round ....I pulled the bolt back to reveal TWO pieces of brass. Its been a while since I posted on the subject because I wanted to get to the bottom of this before I said anything. The rifle's accuracy is not something I can complain about. It seems to shoot fine, but is a nightmare when it comes to ejecting brass, etc. My friend who taught me a lot about shooting still has many friends that he met throughout scout sniper school. One of those is a gunsmith who builts custom rifles. After I showed my friend the problems I was having with my LRH111, he wanted to take it to the gunsmith he knows. The gunsmith that he sent my rifle off to did some basic tests first to see if it was a head-spacing issue. After looking at some of my fired brass he was afraid the rifle might be over chambered. So he sent it off to his friend to have it air mikd on his own equipment. Anyhow, I was told the following: (I may not be repeating it correctly so bear with me) The gun smith said the air miked results show that is it over chambered in shoulder length by .003 (three-thousandths) of an inch. This is making the brass slap up against the chamber when fired and stretching the brass much more than normal. No wonder I was trimming it all the freaking time. The tests ALSO show that it is "out of round" inside the chamber. So bad news on two major issues. There is no way the gunsmith can fix anything like that obviously, so it is fixing to go back to Savage. The gunsmith supposedly has contacts at Savage and is going to call them up to explain the situation and provide all the results that I need. I dont see how they can "fix" an issue like that without replacing the entire chamber. I have not even fired over 200 rounds through the barrel so its pretty new. I will follow up with another post once I hear back from Savage. I plan on mailing it to them sometime next week. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Savage 111 LRH 338 Lapua
Top