Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Reloading
Quick load vs pressure signs
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="bigedp51" data-source="post: 1504826" data-attributes="member: 28965"><p>To get the most out of Quickload your actual case capacity and a chronograph is needed. And you change the burn rate in Quickload until the velocity matches the chronograph. Meaning you need a accurate starting point to calibrate Quickload. </p><p></p><p>The rat turd in the violin case simply means a full length resized case vs the elephant turd in a violin case or neck sized case. Meaning the full length resized case body has "NO" guiding effect on the bullet.</p><p></p><p>Your fecal debris statement has nothing to do with the amount of shoulder bump, and simply deals with case body clearance in the chamber.</p><p></p><p><span style="color: #0000b3">"a full-length sized case in which the neck is also fully sized. There is clearance at the neck and in the body of the case, the closest fit anywhere is the bullet in the throat. If the neck to bullet concentricity is good (although it needn't be perfect), then the bullet will find good alignment in the throat and the case body and neck will have minimal influence. Let's not forget that the base of the case is supported by the bolt face or the extractor to a certain degree as well; this is yet another influence on alignment. As you can see, there are several points from base to bullet that can have an effect. My procedure is to minimize the influence of those that I can control, namely the case body and neck, and let the alignment be dictated by the fit of the bullet in the throat and to some extent by the bolt's support of the base. Barring a seriously out of square case head, I don't think the bolt can have a negative effect on alignment, only a slightly positive effect from minimizing "case droop" in the chamber. Given that a resized case will usually have a maximum of 0.001" diametrical clearance at the web, this isn't much of a factor anyway.</span></p><p><span style="color: #0000b3"></span></p><p><span style="color: #0000b3">In conclusion, I believe that allowing the bullet to find a relatively stress-free alignment in the throat by full length sizing (including the neck) and turning necks to enhance concentricity gives the bullet the best probability of a well-aligned start into the rifling."</span></p><p><span style="color: #0000b3"></span></p><p><span style="color: #0000b3">The Rifleman's Journal</span></p><p><span style="color: #0000b3">Germán A. Salazar</span></p></blockquote><p></p>
[QUOTE="bigedp51, post: 1504826, member: 28965"] To get the most out of Quickload your actual case capacity and a chronograph is needed. And you change the burn rate in Quickload until the velocity matches the chronograph. Meaning you need a accurate starting point to calibrate Quickload. The rat turd in the violin case simply means a full length resized case vs the elephant turd in a violin case or neck sized case. Meaning the full length resized case body has "NO" guiding effect on the bullet. Your fecal debris statement has nothing to do with the amount of shoulder bump, and simply deals with case body clearance in the chamber. [COLOR=#0000b3]"a full-length sized case in which the neck is also fully sized. There is clearance at the neck and in the body of the case, the closest fit anywhere is the bullet in the throat. If the neck to bullet concentricity is good (although it needn't be perfect), then the bullet will find good alignment in the throat and the case body and neck will have minimal influence. Let's not forget that the base of the case is supported by the bolt face or the extractor to a certain degree as well; this is yet another influence on alignment. As you can see, there are several points from base to bullet that can have an effect. My procedure is to minimize the influence of those that I can control, namely the case body and neck, and let the alignment be dictated by the fit of the bullet in the throat and to some extent by the bolt's support of the base. Barring a seriously out of square case head, I don't think the bolt can have a negative effect on alignment, only a slightly positive effect from minimizing "case droop" in the chamber. Given that a resized case will usually have a maximum of 0.001" diametrical clearance at the web, this isn't much of a factor anyway. In conclusion, I believe that allowing the bullet to find a relatively stress-free alignment in the throat by full length sizing (including the neck) and turning necks to enhance concentricity gives the bullet the best probability of a well-aligned start into the rifling." The Rifleman's Journal Germán A. Salazar[/COLOR] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Reloading
Quick load vs pressure signs
Top