Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
New 30/375 wildcat
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="midnightmalloy" data-source="post: 569576" data-attributes="member: 25605"><p>Rich here is the scoupe on what I was trying to convey in an earlier post.</p><p> </p><p>Gunwerks is having brass made by hornady for there 7mm LRM. This will be out in febuary so no forming of brass to get it there.</p><p> </p><p>The 7mm LRM has a longer neck than the 375 ruger or the 30/375 wildcats Ive read about. So i believe this is what you are looking for. </p><p> </p><p>Once the brass is out in febuary you can just buy it from Gunwerks at roughly $1.25 a piece. Then all you would have to do is buy your custom reamer and ONE SET of custom dies. no forming dies!</p><p> </p><p>1. Run the 7mm LRM brass over your expander ball to go up to 30 cal.</p><p>2. fireform in your custom 40*shouldered chamber</p><p>3. Reload and your done.</p><p> </p><p>once the brass comes out in febuary this is like taking 270 win brass and forming it to a 280 AI chamber. THis would reduce the number of steps dramatically and significantly reduce your cost of this project. If you talk to aaron at gunwerks again ask about there headstamed brass and not the stuff they are forming from 375 basic brass. </p><p> </p><p>I think this is a great sounding project. Its the same reason im going with the 7LRM for my current project. fits in a standard magnum action with no mods, can feed from any mag with the long vlds seated so they wont push into the case. send a 180 vld at 3150fps sounds good to me. what your talking about sounds like it would push them good. I would think 79gr of H1000 would fit easily in that case.</p></blockquote><p></p>
[QUOTE="midnightmalloy, post: 569576, member: 25605"] Rich here is the scoupe on what I was trying to convey in an earlier post. Gunwerks is having brass made by hornady for there 7mm LRM. This will be out in febuary so no forming of brass to get it there. The 7mm LRM has a longer neck than the 375 ruger or the 30/375 wildcats Ive read about. So i believe this is what you are looking for. Once the brass is out in febuary you can just buy it from Gunwerks at roughly $1.25 a piece. Then all you would have to do is buy your custom reamer and ONE SET of custom dies. no forming dies! 1. Run the 7mm LRM brass over your expander ball to go up to 30 cal. 2. fireform in your custom 40*shouldered chamber 3. Reload and your done. once the brass comes out in febuary this is like taking 270 win brass and forming it to a 280 AI chamber. THis would reduce the number of steps dramatically and significantly reduce your cost of this project. If you talk to aaron at gunwerks again ask about there headstamed brass and not the stuff they are forming from 375 basic brass. I think this is a great sounding project. Its the same reason im going with the 7LRM for my current project. fits in a standard magnum action with no mods, can feed from any mag with the long vlds seated so they wont push into the case. send a 180 vld at 3150fps sounds good to me. what your talking about sounds like it would push them good. I would think 79gr of H1000 would fit easily in that case. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
New 30/375 wildcat
Top