Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Hunting
Long Range Hunting & Shooting
Damage Done...???
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="25792SP" data-source="post: 299447" data-attributes="member: 18948"><p>Action: Savage 112</p><p>Caliber: 257WBY. (Not original factory caliber)</p><p> </p><p>I was out testing some loads today, working up some new combinations, and going up in powder incriments, obviously got a little too hot and pierced a primer. (This is the first time this has happened to me, I'm not one to knowingly push the envelope!!) </p><p> </p><p>The bolt needed some good muscle to lift, and I had to tap the case out with a cleaning rod. OBVIOUSLY TOO HOT!</p><p> </p><p>OK, so I came home wondering and hoping I had not done any damage to the rifle, came on the forums here, and tried to find what sort of damage to look for.</p><p> </p><p>The case did not fail or crack, (it simply stuck in the chamber). To me, the locking lugs look fine.</p><p> </p><p>The only thing I noticed (which may be a totally unrelated development which I overlooked previously - because I wasn't looking!!... is that the hex bolt on the end of the bolt that holds the bolt handle on was loose - I could turn it off by hand. Would a hot round have caused this? From what I'm reading here on the forums, this hex-bolt is normally <u>extremely</u> tight. Obviously, this action has had work done to it so I'm thinking that it's also possible that the Gunsmith may have simply not tightened it enough and I've never noticed it before.</p><p> </p><p>Does what has happened here raise any red flags with you more experienced reloaders? (other than the obvious fact that I need to back off on the powder) </p><p> </p><p>Is a pierced primer reason enough to suspect bold damage?</p><p> </p><p>Other than the case sticking in the chamber, the shot that pierced the primer seemed normal - no odd smoke or gas blow-backs.</p><p> </p><p>How would I go about re-tightening the hex-bolt to it's proper torque?</p><p> </p><p>Any thoughts?</p><p> </p><p>Thanks guys! I really appreciate your input! I'm not a gunsmith so this development is a bit new to me.</p></blockquote><p></p>
[QUOTE="25792SP, post: 299447, member: 18948"] Action: Savage 112 Caliber: 257WBY. (Not original factory caliber) I was out testing some loads today, working up some new combinations, and going up in powder incriments, obviously got a little too hot and pierced a primer. (This is the first time this has happened to me, I'm not one to knowingly push the envelope!!) The bolt needed some good muscle to lift, and I had to tap the case out with a cleaning rod. OBVIOUSLY TOO HOT! OK, so I came home wondering and hoping I had not done any damage to the rifle, came on the forums here, and tried to find what sort of damage to look for. The case did not fail or crack, (it simply stuck in the chamber). To me, the locking lugs look fine. The only thing I noticed (which may be a totally unrelated development which I overlooked previously - because I wasn't looking!!... is that the hex bolt on the end of the bolt that holds the bolt handle on was loose - I could turn it off by hand. Would a hot round have caused this? From what I'm reading here on the forums, this hex-bolt is normally [U]extremely[/U] tight. Obviously, this action has had work done to it so I'm thinking that it's also possible that the Gunsmith may have simply not tightened it enough and I've never noticed it before. Does what has happened here raise any red flags with you more experienced reloaders? (other than the obvious fact that I need to back off on the powder) Is a pierced primer reason enough to suspect bold damage? Other than the case sticking in the chamber, the shot that pierced the primer seemed normal - no odd smoke or gas blow-backs. How would I go about re-tightening the hex-bolt to it's proper torque? Any thoughts? Thanks guys! I really appreciate your input! I'm not a gunsmith so this development is a bit new to me. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Hunting
Long Range Hunting & Shooting
Damage Done...???
Top