6.5 Creedmoor build 2K budget

Just remember light recoil equals light impact! Physics plain and simple when you pull the trigger an equal amount of force is applied both directions!
I would use a 300WM before a 6.5CM!
I would disagree with that. My 6mm cm pushes a 105g to 3100 on 42g, faster than a 243 while using less powder. Same with the 7 blaser mag pushing a 195 to 3000fps on 64-69 g vs 70-90g in larger cases.
 
OK Cool you can have your opinion but you are only talking about speed?
Let's discuss Foot Pounds Of Energy. I can run a 70 Gr out of my 22-250
that is faster than your 6mm or a 100 Gr out of my 25-06 that averages
3300 FPS! But that sure doesn't make either one an Elk rifle! It's what happens when they get there that matters!
 
Last edited:
OK Cool you can have your opinion but you are only talking about speed?
Let's discuss Foot Pounds Of Energy. I can run a 70 Gr out of my 22-250
that is faster than your 6mm or a 100 Gr out of my 25-06 that averages
3300 FPS! But that sure doesn't make either one an Elk rifle! It's what happens when they get there that matters!
not at all your completely missing physics and my point of view. i was comparing small yet subtle differences in very similar calibers. A 6mm cm and a 243 are basically identicle, yet the 6cm is slightly faster and uses less powder, therefore there is less felt recoil than an equally performing (speed) 243. Just as the 7 blaser vs 7rm or equal speed load in a 7rum etc
 
If your friend wants to go with 6.5CM, I suggest you help enhance velocity with a 26" barrel and go with long, tough Bullets like 140gr Accubond or 139gr Scenar, at well over 2800fps. Maybe the X-Bolt Hell's Canyon LR?
 
I'm not one to pour gas on the fire, but, while the 6.5 CDM will do the job, there are better choices out there as a dedicated elk rifle. BUT with the proper bullet and within proper ranges, 6.5 CDM will do ok.

Check out the Christensen Arms Mesa rifle.
 
If it were me, 270 or 30-06 for a non magnum gun, or a 7mm 30 cal magnum. I have a 7mm STW & RUM even though the others can do the job that would be "my" minimum guns. I do have a Howa 270 that shoots very well. It's stainless, with the rubber coated stock, & a Leupold VX3. I have less than $1200 in it, but it shoots sub moa all day and would be good to 4-500 yards on a elk with the right bullet (LR Accubond)
 
Last edited:
I would do the savage 110 high country 6.5prc (ballistics are better and more energy) and a Nightforce SHV scope, 20 moa base and some rings. Slap a small lightweight bipod on there and be done. I think it would be a great little rifle and he would be able to use it for multiple applications.
 
6.5mm is a bad idea for ELK. If you're on a budget do this:

Rem700LR(7mm rem mag or 300 win mag) $700 in your hands (https://www.budsgunshop.com/catalog/mobile/product/79957/redirect) - this is an amazing deal considering it comes with a $280 bell and Carlson stock with integral aluminum bedding block. And if it won't shoot you only have about $400 in the action so you have a good start to a custom rifle.

Factory trigger is serviceable ($100-150 Timney or trigger tech optional)

Glass bedding (easy to dIY for $15 jb weld but $100-150 at gunsmith)

Sightron siii 3.5-10x44mm ($650 new) - best glass/tracking for the $ IMO

Harrels prescion muzzle brake ($100-150 install by gunsmith) - will reduce recoil by 70% and allow you to spot your impacts over 3-400yds.

Get a good 20moa steel one piece scope base (<$100, recommend tps)

TPS aluminum low 30mm rings ($120) - recommend aluminum rings due to different thermal expansion of steel/aluminum, don't want to stress scope tube.

That's a total of $1870 (conservatively) for a 1moa 1000yd hunting rifle. If you reload great, if not, you can buy good 7mmRM/300WM at any gun shop.
 
Looking to build a 6.5 Creedmoor for an elk hunt this fall. Have a 2k budget for the package (including optics) what would you guys recommend? I have built full custom rifles in the past, but not really done a lot of making long range rifles based off of factory builds. Something factory that would fit the bill with some gunsmithing...or recommend something else? Could maybe push the budget another $500 if need be.
If you are building the rifle yourself, yes it's doable at the $2000.00 mark
 
Warning! This thread is more than 6 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top