Let's see your Varmint rifles !

[SAVAGE22-243AI]

The Money Mostly, I have plenty of time on my hands to make my own out of the thousands of .243 cases I have. I also anneal them too, so they look like Lapua brass when finished.

Here is my boys 22-250 AI.............Savage, SSS stock, 13 ounce trigger, factory barrel 1-12. But he fights me for one of my 22-243 AI's. But Dad! I can't see where the bullet hits with my rifle.

 

[samiller]

Here is my latest.

Savage target action
Brux, 22-250AI 1-9 twist
Lowrider stock

 

[liltank]

Here is my latest.

Savage target action
Brux, 22-250AI 1-9 twist
Lowrider stock

Very nice first post and rifle. Where abouts are you from?

 

[samiller]

Very nice first post and rifle. Where abouts are you from?

Thanks!
I'm from southeastern, PA.

 

[bowhunthard88]

Here is my latest.

Savage target action
Brux, 22-250AI 1-9 twist
Lowrider stock

I second liltank: That's a NICE rifle!

 

[meatyrem]

Heck. Most times I only see one or two woodchucks. It would be nice to see that many in the same day.

 

[bowhunthard88]

Heck. Most times I only see one or two woodchucks. It would be nice to see that many in the same day.

LOL . Here's another pic of my 22-250 Savage LRPV:

 

[samiller]

Heck. Most times I only see one or two woodchucks. It would be nice to see that many in the same day.

I hear you,
I must say that was a good day!
I had one more that didnt make into the picture.

 

[liltank]

I hear you,
I must say that was a good day!
I had one more that didnt make into the picture.

I need to find some new hunting grounds!

 

[Hunter2678]

Just as a reference this gun started out as a mod 12 fcv in 22-250 a few pages back on this thread. (pg 39, pg43)

and now after much evolution we have a finished product: 6mm BR.

Kreiger 8 twist, 1.25 OD no taper, bead blasted, recessed target crown, .269 neck, .104 freebore, reinforced CM 4140 recoil lug, "nutless" trued savage short action, fully bedded, lapped lugs,lapped lug channels, trued bolt face, HS precision M24 varmint/tact stock, rifle basix sav-2 trigger @ 11 oz., SSS fred sled, SSS tactical bolt, Burris tactical xtra tall rings, Zeiss conquest 6.5-20 mil dot and a harris BR bipod up front. Tips the scales at 17lbs.

 

[Truc]

Not the best pic, not enough light. It is 6 for 6 as far as grounhogs go and will shoot less than .3" at 200 yds w/ Varget powder and 105 Berger bullets

Kelbly Atlas action single shot w/ fluted bolt
1-8 twist Spencer barrel HV chambered in a 6 Dasher or 6DJ .264 neck
H&S Precision Benchrest stock bedded
Jewell Trigger
4X16 Weaver scope mounted in Kelbly rings

 

[trebark]

These two most recent additions to this thread, their scopes are mounted really high. Must be tough getting a good cheek weld without an adjustable cheekpiece.

 

[6.5x61Super]

my number 1 goto:

..switch to 1080p for higher res...

[ame=http://www.youtube.com/watch?v=zSi2pzwZfOg]6.5x61Super Ohio Groundhog and Big Buck.wmv - YouTube[/ame]


[ame=http://www.youtube.com/watch?v=Ljyvh5FC734]Ohio Groundhog 3 misses 6.5x61Super - YouTube[/ame]


[ame=http://www.youtube.com/watch?v=a3FsPii8W-E]Ohio Groundhog Redemption 6.5x61Super - YouTube[/ame]

 

[Hunter2678]

These two most recent additions to this thread, their scopes are mounted really high. Must be tough getting a good cheek weld without an adjustable cheekpiece.

Funny you say that..I actually replaced the xtra talls with the 3/4 height tact rings today...the height was getting uncomfortable in the prone position. I wanted to see if they would be doable in both prone and bench but not with my neck it seems. They were great off the bench though.