Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Need groove advise...3 or 6?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="AZShooter" data-source="post: 802585" data-attributes="member: 5219"><p>I am by no means an expert but the three groove will not put a land opposite another land which the 6 groove will. I have heard one reason is the idea behind non opposing lands is theoretically less stress on the bullet. Below Dan Lilja talks about less throat erosion. </p><p></p><p>I have had two 3 groove liljas. Can't say if the number three is the cause BUT once the throats became worn they would cause VLDs to become damaged and the rifle would shoot flyers. The same thing might happen with a 6 groove but don't know. </p><p></p><p>Here is what I HAVE observed:</p><p></p><p>First 3 groove was an ill advised 1 in 7 twist in 7 Rem mag to shoot the 180 VLD. At round count 225 or so the rifle would shoot occasional flyers that would diverge as much as 3 ft off POI at 100 yds! I think the twist was responsible for the bullet coming apart with such a low round count. </p><p></p><p>The second 3 groove faired better. It is a 1 in 10 twist 257 weatherby. I shot 115 VLDs to approx. round count of 550 then began to shoot flyers. Not as far off POI but enough for me to switch to a bullet that would not be affected by the rough throat. Now shooting a 110 accubond. Round count is close to 1000 and while it is a nasty fouler and looks horrid through a borescope it still is very accurate. </p><p></p><p>I have no idea if a 6 groove would have done the same thing or not. </p><p></p><p></p><p>Here is what Dan Lilja says:</p><p></p><p>Q. What are the differences between 3 Groove and 6 Groove Barrels? </p><p></p><p>A. Almost all of the caliber and twist combinations in the rifle barrels we make are available with 6 lands and grooves. A few years ago we started to make barrels in a 3 groove configuration too at the request of some varmint hunters who were looking for longer barrel life. They were chambering barrels for hot 22 caliber varmint rounds and shooting the throats out of conventional 6 groove barrels fairly fast. We reasoned that if we reduced the number of grooves to 3 but kept the ratio of land to groove width the same (ie. the lands are twice as wide in a 3 groove barrel as compared to a 6 groove) that there would be more land area to resist heat erosion. </p><p></p><p>Well, it turned out that barrel life did increase and that accuracy stayed at least the equal of comparable 6 groove barrels. It is hard to put a percentage increase on barrel life but a conservative estimate might be 20%. </p><p></p><p>Benchrest shooters are always experimenting and looking for a competitive edge. Before long a few shooters, including Dan Lilja, were putting 3 groove barrels in 6PPC and 22 Waldog on their light varmint and heavy varmint class benchrest rifles. And these barrels proved to be very accurate. They started winning benchrest matches and soon became popular among the benchrest shooters. . </p><p></p><p>On the right is Dan with a .193" 200 yard group fired at a benchrest match in Billings Montana in 1998. </p><p></p><p>This was with a 6 mm PPC 13" twist 3-Groove Barrel. </p><p></p><p>And we found that as a side benefit the 3 groove barrels seemed to foul very little and clean up quickly. We attributed this to the reduced number of corners inside collecting powder and copper fouling. </p><p></p><p>This answer to 3 groove - 6 groove question is not meant to discredit the 6 groove barrels. They have consistently shoot extremely well over the years. Dan continues to shoot both 6 and 3 groove barrels on his benchrest rifles. But if you haven't tried a 3 groove you might consider one the next time you need a barrel. We do not offer them in all of our caliber and twist combinations. Our page with caliber and twist listings indicates if a 3 groove barrel is available. And we are frequently adding 3 groove buttons to our offerings. If you don't see that a 3 groove version is offered in the caliber and twist you're looking for, ask, we might soon be making it.</p></blockquote><p></p>
[QUOTE="AZShooter, post: 802585, member: 5219"] I am by no means an expert but the three groove will not put a land opposite another land which the 6 groove will. I have heard one reason is the idea behind non opposing lands is theoretically less stress on the bullet. Below Dan Lilja talks about less throat erosion. I have had two 3 groove liljas. Can't say if the number three is the cause BUT once the throats became worn they would cause VLDs to become damaged and the rifle would shoot flyers. The same thing might happen with a 6 groove but don't know. Here is what I HAVE observed: First 3 groove was an ill advised 1 in 7 twist in 7 Rem mag to shoot the 180 VLD. At round count 225 or so the rifle would shoot occasional flyers that would diverge as much as 3 ft off POI at 100 yds! I think the twist was responsible for the bullet coming apart with such a low round count. The second 3 groove faired better. It is a 1 in 10 twist 257 weatherby. I shot 115 VLDs to approx. round count of 550 then began to shoot flyers. Not as far off POI but enough for me to switch to a bullet that would not be affected by the rough throat. Now shooting a 110 accubond. Round count is close to 1000 and while it is a nasty fouler and looks horrid through a borescope it still is very accurate. I have no idea if a 6 groove would have done the same thing or not. Here is what Dan Lilja says: Q. What are the differences between 3 Groove and 6 Groove Barrels? A. Almost all of the caliber and twist combinations in the rifle barrels we make are available with 6 lands and grooves. A few years ago we started to make barrels in a 3 groove configuration too at the request of some varmint hunters who were looking for longer barrel life. They were chambering barrels for hot 22 caliber varmint rounds and shooting the throats out of conventional 6 groove barrels fairly fast. We reasoned that if we reduced the number of grooves to 3 but kept the ratio of land to groove width the same (ie. the lands are twice as wide in a 3 groove barrel as compared to a 6 groove) that there would be more land area to resist heat erosion. Well, it turned out that barrel life did increase and that accuracy stayed at least the equal of comparable 6 groove barrels. It is hard to put a percentage increase on barrel life but a conservative estimate might be 20%. Benchrest shooters are always experimenting and looking for a competitive edge. Before long a few shooters, including Dan Lilja, were putting 3 groove barrels in 6PPC and 22 Waldog on their light varmint and heavy varmint class benchrest rifles. And these barrels proved to be very accurate. They started winning benchrest matches and soon became popular among the benchrest shooters. . On the right is Dan with a .193" 200 yard group fired at a benchrest match in Billings Montana in 1998. This was with a 6 mm PPC 13" twist 3-Groove Barrel. And we found that as a side benefit the 3 groove barrels seemed to foul very little and clean up quickly. We attributed this to the reduced number of corners inside collecting powder and copper fouling. This answer to 3 groove - 6 groove question is not meant to discredit the 6 groove barrels. They have consistently shoot extremely well over the years. Dan continues to shoot both 6 and 3 groove barrels on his benchrest rifles. But if you haven't tried a 3 groove you might consider one the next time you need a barrel. We do not offer them in all of our caliber and twist combinations. Our page with caliber and twist listings indicates if a 3 groove barrel is available. And we are frequently adding 3 groove buttons to our offerings. If you don't see that a 3 groove version is offered in the caliber and twist you're looking for, ask, we might soon be making it. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Need groove advise...3 or 6?
Top