Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Reloading
neck size or full length size?????
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="john g duvall" data-source="post: 340413" data-attributes="member: 22083"><p>Hello "Big Buck". I use a custom built Akley Improved 300 Win Mag. Lonnie Hummel (CHIEF ENGINEER) of Hornady out in Grand Island Nebraska said I needed full sized dies($300.00!!!) If it loads properly then look at this. It is from Sept 2009 at 400 yards. Notice that my powder loads were not "on" until I hit 71.2 grains of R-22. The last three shots were at 71.2 gr. There are 8 witness signatures that verify 3 holes on the cross hairs at 400 yards. I put two of these holes there. Don Sanders put the third "hole in a hole". It measured .523 inch. covered it with a dime. It is the weapon and load that works. Donny is 5'9" tall and weighs about 240lbs. I'm 6'1" and weigh 195. Two different breathing patterns, heart beats, eye reliefs etc. with the same result. Full size works with Nosler 5 star custom brass, Fed GMM 215 primers, 71.2 gr of R-22 and seating a 210 grain Sierra HPBT Matchking(BC.650) at .001 to the lans and grooves. T. Sarver set the 1000 record using a 240 gr. Sierra BTHP Matchking out of a .338 Lapua necked down to 30 cal. 1.4 inch 5 shot group, scored 50 five x!!!! It is on the web so...check it out. My picutre won't load so write and I'll send it. <a href="mailto:johngduvall@windstream.net">johngduvall@windstream.net</a></p></blockquote><p></p>
[QUOTE="john g duvall, post: 340413, member: 22083"] Hello "Big Buck". I use a custom built Akley Improved 300 Win Mag. Lonnie Hummel (CHIEF ENGINEER) of Hornady out in Grand Island Nebraska said I needed full sized dies($300.00!!!) If it loads properly then look at this. It is from Sept 2009 at 400 yards. Notice that my powder loads were not "on" until I hit 71.2 grains of R-22. The last three shots were at 71.2 gr. There are 8 witness signatures that verify 3 holes on the cross hairs at 400 yards. I put two of these holes there. Don Sanders put the third "hole in a hole". It measured .523 inch. covered it with a dime. It is the weapon and load that works. Donny is 5'9" tall and weighs about 240lbs. I'm 6'1" and weigh 195. Two different breathing patterns, heart beats, eye reliefs etc. with the same result. Full size works with Nosler 5 star custom brass, Fed GMM 215 primers, 71.2 gr of R-22 and seating a 210 grain Sierra HPBT Matchking(BC.650) at .001 to the lans and grooves. T. Sarver set the 1000 record using a 240 gr. Sierra BTHP Matchking out of a .338 Lapua necked down to 30 cal. 1.4 inch 5 shot group, scored 50 five x!!!! It is on the web so...check it out. My picutre won't load so write and I'll send it. [EMAIL="johngduvall@windstream.net"]johngduvall@windstream.net[/EMAIL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Reloading
neck size or full length size?????
Top