Primer Seating?

I have recently started using primer pocket gauges to check the brass after decapping and before sizing. I had to"retire" a lot of Federal brass from my 224 Valkyrie for loose pockets. I never had an issue with Lapua or ADG or Peterson brass. I also do not "hot rod" my loads since I mainly shoot benchrest. Loose prime pockets are indeed dangerous both to the equipment and the shooter.
 
Like a swage on military rounds?
There is a tool to remove the swage but have not seen a tool to give it the swage like some I have seen on military rounds

Fired up the 1024 lathe, modified the large primer pocket swaging spud.

20220811_135341.jpg


Set up in the press is the same as swaging operation.

20220811_140009.jpg


Proving the concept. It works, take a closer look you can see the circular mark around the primer. I stop at this minimal testing till I heat treat the crimping edge. The knife edge may not last long. I also do not like the way the die centers the case. Too much slop for this application. In swaging it does not matter, the primer pocket aligns the case. My plan is to modify a neck sizer with the correct length swaging rod that goes inside the die that bears against the opposite side of the primer pocket.

20220811_140322.jpg


My thinking the application is for the brass heading to the recycle bin to give it one last hoorah before discarding.

Thoughts?
 
I made a similar modification to the swaging stud and it works. Unfortunately, now I'm using an Zero press and the case stripper doesn't fit over the ram. I need to make an oversized case stripper when I need to do this again.
 
When brass is done, it's done. The key is to perform proper work ahead of time to ensure it's not done too early in it's life and you get the use you want out of it.

This comes in the form of proper vetting of sizing dies, processes, and load pressures.

I won't knock your ingenuity however. ;)


-----------
Follow on Instagram
Subscribe on YouTube
Amazon Affiliate


Thank you for the input, and the kind words.
 
A while back, someone posted a chart that showed how primers of different brands are slightly different dimensionally. Sometimes switching to another brand of primer will solve this issue of loose fit. This assumes of course, you have a selection of various primers in lean times.
I couldn't find the post but someone can probably retrieve it.
 
When I started with the 260 several years ago, I bought my buddies dies, a bunch of brass and bullets. While priming (CCI 200) I found some with loose pockets, at least looser than others. I started measuring and they were at the high end of the spec at .210". I wasn't comfortable with them, so I went through all of the brass and tossed anything that measured .210" or larger. They probably would've been fine, but not worth me taking a chance.
 
Might help
 

Attachments

  • 5136C776-59E8-4AEB-A2D9-37949916FCB3.png
    5136C776-59E8-4AEB-A2D9-37949916FCB3.png
    71.1 KB · Views: 42
  • A740A1EC-C273-4902-9C46-12B914941B5D.png
    A740A1EC-C273-4902-9C46-12B914941B5D.png
    105.5 KB · Views: 37
  • 0381F823-BD09-4ADB-A35D-AF6981395C6E.png
    0381F823-BD09-4ADB-A35D-AF6981395C6E.png
    117.3 KB · Views: 44
  • A08B23A1-8F3D-4F81-BDC2-D6689F4AEF9F.png
    A08B23A1-8F3D-4F81-BDC2-D6689F4AEF9F.png
    128.9 KB · Views: 41
  • 09DA396E-A4CF-496D-9666-F088924AEB45.png
    09DA396E-A4CF-496D-9666-F088924AEB45.png
    113.7 KB · Views: 43
  • 634B50E0-BB82-405E-9CFD-632AE4EEE35A.png
    634B50E0-BB82-405E-9CFD-632AE4EEE35A.png
    91.8 KB · Views: 41
  • 915ADC31-F9DE-4513-B160-6F63CB60AB30.png
    915ADC31-F9DE-4513-B160-6F63CB60AB30.png
    7.4 KB · Views: 40
I have had this issue from time to time. Starting withNew Winchester Brass, in 270 Win, Loaded in my Weatherby Ultralight. Using the RCBS Primer seating tool, I can really tell the difference between a properly seated Winchester LR primer, and the occasional one that just goes in Super easy . This may occur about the 4th or 5th loading of that same batch of matched Winchester cases, used in one specific rifle, with Winchester LR Primers. So I am really happy to be reading this thread, and I have sent for the Go/No-go gauges today. Loading for over 55 years , and STILL LEARNING!!!! By The way is there an Industry Spec for the Dia. of all Large Rifle/ Large Rifle Magnum Primers???Thank You all
 
Top