Piercision Rifles 300 WSM

rpierce

Official LRH Sponsor
Joined
Oct 8, 2009
Messages
768
Location
Waucoma, IA
Well load testing is done on my new 300 WSM I did on a long action Defiance ANTIX with a 23" Benchmark carbon barrel. Running a 215 berger at a mild 2685 fps and a ES of 8-12 fps for 10-18 shots. Most consistent load Ive tested PERIOD. Using .005 neck tension. Powder charge node is almost a grain wide. Did a seating depth test and had 5" vertical for 18 shots at 840 yds. 3 shots per seating depth. Most were 3" or less vertical at 840 yds. .029-.032 off shot the smallest though. This rifle and load has shot a pile of awesome groups already. Every time I take it to my 840 yd target its under 1/2 moa vertical.

Rifle has the following:
Defiance ANTIX
Manners LRH in high plains camo
Benchmark 23" 9.0 tw sendero light
Hawkins Hunter bottom metal and 3 round flush mag w spacer
Triggertech Diamond set at 1.5 lbs
Nightforce ATACR 4-20
TBAC Dominus SR suppressor
MDT lightweight double pull bipod.

Weighs 9 lbs 12 oz with optics and no suppressor or bipod. 10 lbs 10 oz with suppressor.
My goal for this rifle was to have a mild and stupid accurate load in the 300 wsm so I would get 2000+ rounds of benchrest accuracy out of it. The powder Im running is cool burning and clean. Ive had almost zero throat erosion so far. In the neighborhood of 15xs less throat erosion than a 28 nosler would at this point. The 215 at 2685 FPS still has enough energy to take elk at 900+ yds. And the difference in wind drift between the 215 at 2685 FPS and the bigger magnums isn't as much as youd think. You cant shoot or call the difference in wind. Only difference between the wsm and my norma improved would be down range energy.

www.piercisionrifles.com
345239612_1488849011883258_7642183152472748459_n.jpg
345128109_2280080885504712_5411334952712632272_n.jpg
345078196_642095494491601_5102000204252988711_n.jpg
345128131_919941365758804_2131474101227213847_n.jpg
300 wsm 100 yds.jpg
3 shots at 580 yds wsm.jpg
840 yds.jpg
4@840 wsm.jpg
 
Very nice shooting and good looking rifle !
I have found my WSM likes more neck tension than my other rifles. Are you setting the .005 with just a bushing die ?
Mandrel ?
 
Very nice shooting and good looking rifle !
I have found my WSM likes more neck tension than my other rifles. Are you setting the .005 with just a bushing die ?
Mandrel ?
Thank you. Yes. Im running a bushing, no mandrel. Running the neck into graphite lube after sizing and then running it through a nylon brush to remove the majority of the graphite. Too much lube and groups and ES doubled.
 
Once again, very impressive rifle Ryan. You should know how to build them, load for them, and shoot them. Nice work! You’re making me want a WSM
 
Well I decided to send a few more rounds at my 840 yd plate this morning with my 300 WSM. 4 shots measured 2.559"/.29 moa @ 840 yds. Vertical was 1.687"/.191 moa. I woulda sent the 5th shot but the wind picked up when I was getting ready to send it. Looks like 5 shots on the target but one of em is from a previous group that was painted over. Not bad for a 20x scope off a bipod. Shes a tack driver.
840 yd 4 shot.jpg
840 yds 4 shots.jpg
 

Recent Posts

Top