Ladder Test

devildoc

Well-Known Member
Joined
Feb 10, 2006
Messages
285
Location
Pueblo, CO
[image]http://viewmorepics.myspace.com/index.cfm?fuseaction=viewImage&friendID=70860019&imageID=653831503&MyToken=1bb012e5-80db-4fda-b059-ff0cc15ece3e[/image]

Grains Velocity
1.) 24.5 3142
2.) 24.7 3196
3.) 24.9 3176
4.) 25.1 3207
5.) 25.3 3284
6.) 25.5 3270
7.) 25.7 3311
8.) 25.9 3225
9.) 26.1 3396
10.)26.3 3407
11.)26.5 3415

Shot at 200 yds., powder=benchmark 24.5-26.5 grains, .2 gr increments (nosler manual) bullet=50gr. nosler bal. tip.

Ok I think this is pretty much a no-brainer, gotta be the #5 load, right?
 
[image]http://viewmorepics.myspace.com/index.cfm?fuseaction=viewImage&friendID=70860019&imageID=653831503&MyToken=5cf51582-313e-4796-bb61-ab307b141e64[/image]
 
Here you go.

653831503_l.jpg


When you can see the picture, whereever it is on the net. Right click on it, click properties, highlight the http:whatever making sure it says .jpg at the end. Hit image as you did under the Instant UBB code, hit paste, and there you have it.
 
by the way, #1 was my sighter and it was about 8" directly above #10, so I adjusted 4 MOA down. Which Puts it about a half inch below #10 as I see it. Also, I'm pretty sure I pulled #8 a little right. I was using a Pact model 1, chrono and a CZ 527 american .223 rem.
 
[ QUOTE ]
gotta be the #5 load, right?

[/ QUOTE ]

Maybe not. Those three shots are grouped nicely but the velocities are all over the place. It may well be that those three powder weights shoot well together at 200 yds but as distance increased out towards maximum for the 223 the velocity variation will string them vertically.

Also 3284 isn't much velocity w/the 50gr in a 223. Why not run the ladder test up scale just a little more.

If your satisfied with the 3284 velocity you may wish to consider loading 3 @ 25.2, 3 @ 25.3 and 3 @ 25.4 and shoot three groups of three then overlay the targets and see how it looks. That may well show you some additional things.

Just tho't I'd add my 0.02$

Looks like you have a shooter there.

Good luck and good shootin'
 
I don't really care about velocity that much, 3300 is plenty to make a gopher goosh, I just want to make bugholes as far out as I can. If that load won't get it done and you see somethin' in that shot string more promising, or have any other advice to give, please pipe up.
 
If velocity is so important, does that mean that 10 is best? Sinc 9, 10 and 11 have only a 19fps spread, and 1 moa spread in windage and about 1/2 moa in elevation?

I thought I saw a pattern with 1-3 horizontal stringing, 4-6 a tight node, 7-9 diagonal stringing, 10-11 horizontal stringing, with a likely node .5 gr above #11.
Am I missing the boat?
 
test loads 4, 5 and 6 to confirm repeatable groups and chrono results.

Look for low SD and ES.

Tweak seating depth last up and down.

You did not mention the accuracy of your charges weight. beam or electronic Scale, thrown with measure or what, but that could effect the ladder if not right on.

If loading for a magazine gun, always start at max OAL or if single shot start at a hard jam, and that you only have to work in on seating depth.

BH
 
Warning! This thread is more than 18 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top