full length resizing

Just to be sure you understand, it is best to fine tune the depth of the full length sizing die to the individual rifle's chamber.

Best procedure as stated by last poster is to adjust the sizing die with a space between the shell holder and end of die. How much? Start with a 1/4" space. Lube and size brass. Wipe off brass and try closing the bolt with the brass in the chamber. Most likely there will be resistance about the same as if you put the fired case into the rifle without any sizing.

Adjust the die 1/4 turn lower and size , and try in rifle's chamber. Repeat this process adjusting the die lower by 1/4 turn and trying in the chamber. At some point it will become more difficult to close bolt. This is because you have actually lengthened the case by partially sizing the taper. Continue to move die lower incrementally. Eventually you will get to the correct adjustment where the brass will fit without any bolt closure resistance. You could even move the die upwards very slightly for a hint of bolt closure which some prefer. At this setting you will get long brass life.

While you can tighten the lock ring for future sizings I prefer to use feeler gauges to measure the gap between the die and shell holder. I have a box of loose feeler gauges and will put the necessary gauges in the box for future adjustments. A note on the inside of the box with a sharpie would also suffice.

In my early days of handloading I over sized the brass which eventually caused case head separation! As I fired the round gasses vented through the hole near the receiver of my Ruger. When I opened the bolt only the case head came out with the bolt. The body was still in the chamber! I had to go to a gunsmith where he was able to remove the stuck piece of brass. Not only was this dangerous with the hot gasses venting near my face but it was inconvenient as well. Imagine if it were during a big game hunt!

I sincerely hope the procedure makes sense. If not please ask more questions.

Ross

+1 on this method
 
Im not arguing this. This is true for every press with any die.
Im saying creating more resistance as the press cams over by screwing the die down more, is not necessarily pushing the case further into the die.



This is not true and it is beside the point i was trying to make.
Some cases, when being sized in a particular die, do not need the die to contact the shell holder in order to have the headspace bumped back enough to properly chamber in the rifle they are being sized for.

If you set up your die by contacting it to the shell holder, there is a good chance you could be overworking the case.

The "CAM" is the most upward part of the stroke of your press's arbor.
When you reach this point the press handle is moving the greatest distance relative to the distance traveled by the arbor. You always want to run through this point on any press operation because it assures your arbor is reaching its highest point with the greatest amount of force. This is regardless of the amount play you have in your arbor or its alignment to the die. If the seat is contacting the bottom of the die at this point and you are feeling resistance in the handle, chances are the case is as far into the die as it will be able to go.

In my opinion screwing the die down any further is only stressing the components of your press. You would benefit more from running the case through the die a second time or even removing material from the base of the die or the top of the shell holder, than you would by screwing the die down any further.

SOP for me. You'll find all my dies to be ground on the base and/or the shellholder. Issue is, the base and/or shellholder has to be ground square to the ram axis or they will contact in a skewed manner. No big deal here, I fixture them in a surface grinder and grind them that way. Just a couple thousands, no more (depending on the shoulder bump according to my headspace gage.

If the die is manufactured to SAMMI specification, an interference fit between the die base and the shellholder will almost always bump the shoulder back too far and overwork the brass and in the interests of longevity of cases, you want to bump as little as possible. You have to determine the headspace required and then bump back a couple thousands, no more. The easiest way is to use a fired case and measure the shoulder datum with a repeatable fixture. I use a Hornady gage myself. However, keep in mind that each chamber is different, just like fingerprints, so the fired case must come from the chamber you want to size for....

All dies will set back the shoulder on a bottleneck case when resizing, don't matter if the die is a fixed cavity or a bushing style, bushing style being a better choice for neck tension and you can remove the bushing and expander ball for bumping without sizing.

I run both ways depending on caliber and end use. Smaller calibers like 223 aren't so critical as the internal dimensions are smaller so a fixed cavity will work fine. On larger calibers (3 series and larger), bushing dies are the way to go because the internal dimensions of the die are larger and more room for error.
 
Just to be sure you understand, it is best to fine tune the depth of the full length sizing die to the individual rifle's chamber.

Best procedure as stated by last poster is to adjust the sizing die with a space between the shell holder and end of die. How much? Start with a 1/4" space. Lube and size brass. Wipe off brass and try closing the bolt with the brass in the chamber. Most likely there will be resistance about the same as if you put the fired case into the rifle without any sizing.

Adjust the die 1/4 turn lower and size , and try in rifle's chamber. Repeat this process adjusting the die lower by 1/4 turn and trying in the chamber. At some point it will become more difficult to close bolt. This is because you have actually lengthened the case by partially sizing the taper. Continue to move die lower incrementally. Eventually you will get to the correct adjustment where the brass will fit without any bolt closure resistance. You could even move the die upwards very slightly for a hint of bolt closure which some prefer. At this setting you will get long brass life
While you can tighten the lock ring for future sizings I prefer to use feeler gauges to measure the gap between the die and shell holder. I have a box of loose feeler gauges and will put the necessary gauges in the box for future adjustments. A note on the inside of the box with a sharpie would also suffice.

In my early days of handloading I over sized the brass which eventually caused case head separation! As I fired the round gasses vented through the hole near the receiver of my Ruger. When I opened the bolt only the case head came out with the bolt. The body was still in the chamber! I had to go to a gunsmith where he was able to remove the stuck piece of brass. Not only was this dangerous with the hot gasses venting near my face but it was inconvenient as well. Imagine if it were during a big game hunt!

I sincerely hope the procedure makes sense. If not please ask more questions.

Ross
Tag
 
Warning! This thread is more than 11 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.
Top