Contender reloading

nksmfamjp

Well-Known Member
Joined
Jan 5, 2004
Messages
3,329
I have a couple new to me Contender barrels I'd like to do some reloading for….

The first step in my process (after brass forming) is to pressure test to determine a max load.

So 2 questions…..

When I FL size, how much should I bump the shoulder? Fired cases measure +0.012" plus to the barrel face, but the barrel closes on a 0.003" feeler gage max. I'll recheck and post again later.

What are the pressure signs before frame stretching? This is a Contender not G2. Hard to open? Primers? Other?
 
When you Full-Length resize, you want to bump it 2 thou.
Note: Your first firing will probably not fully form your case.
For your first load, I would jam the bullet into the lands so it pushes the head of the case all the way back into the frame.
Chamberings?
 
30 Herrett….already have fired brass.

7-30 Waters….need to form. Probably follow COW method to avoid using the bullets
 
From Belam's article.
 

Attachments

  • 1E34ED04-3067-47E9-AAAB-6C6C204413AC.png
    1E34ED04-3067-47E9-AAAB-6C6C204413AC.png
    161.9 KB · Views: 89
Anyone have a source fro brass for 30 Herrett?
Got a T/C chambered in it and havent even fired it yet due to lack of ammo. Ive got a reloading set up out in the shop and dies sitting in my MidWayUSA cart.
 
30 Herrett….already have fired brass.

7-30 Waters….need to form. Probably follow COW method to avoid using the bullets
I COW'ed my 7-30 Contender, it seemed to work fine. I would caution against jamming a bullet until you determine your chamber pressure is suitable to allow for it.
 
Anyone have a source fro brass for 30 Herrett?
Got a T/C chambered in it and havent even fired it yet due to lack of ammo. Ive got a reloading set up out in the shop and dies sitting in my MidWayUSA cart.
Size 30-30 brass in the full length dies and trim to length. Fireform and I would recommend annealing the brass. I lost a lot of cases to split necks by skipping this step.
 
30 Herrett….already have fired brass.

7-30 Waters….need to form. Probably follow COW method to avoid using the bullets
I think the thick loose leaf Sierra manual has both listed in their pistol section. Believe contender was used to develop data. I'll post copies of .the data when I get back in the shop tomorrow AM.
 
Sierra 6th Vol data for 7-30 and 30 Herrett. Both were shot in 10" contenders.
 

Attachments

  • 51744BEB-0482-4314-913E-40CA58AC2DEB.jpeg
    51744BEB-0482-4314-913E-40CA58AC2DEB.jpeg
    2 MB · Views: 76
  • 65EA3E1B-219B-4FBF-8098-56B6C5B5D84B.jpeg
    65EA3E1B-219B-4FBF-8098-56B6C5B5D84B.jpeg
    2 MB · Views: 74
  • 38AA8B06-FFB8-4701-82E8-627D1C067C44.jpeg
    38AA8B06-FFB8-4701-82E8-627D1C067C44.jpeg
    2 MB · Views: 74
  • F6BB1657-F735-4F40-A919-CBB61E0FD2A2.jpeg
    F6BB1657-F735-4F40-A919-CBB61E0FD2A2.jpeg
    2 MB · Views: 73
  • 7E4A5B15-0C01-4030-9DD5-202A08D2FB86.jpeg
    7E4A5B15-0C01-4030-9DD5-202A08D2FB86.jpeg
    2 MB · Views: 73
  • 7510160C-8496-4C14-B30E-F15E69A310E6.jpeg
    7510160C-8496-4C14-B30E-F15E69A310E6.jpeg
    2.1 MB · Views: 70
  • 66955181-5046-4599-AAAA-E639F72D67BE.jpeg
    66955181-5046-4599-AAAA-E639F72D67BE.jpeg
    2 MB · Views: 75
  • 5824C01B-D749-44E0-AB43-C3809DD637A6.jpeg
    5824C01B-D749-44E0-AB43-C3809DD637A6.jpeg
    2 MB · Views: 70
I stretched the frame on an Encore in .416 Taylor (by SSK). Shot a sable that needed a second shot. The Encore DID NOT fire! Finished him at 120 yds. with my Ruger SuperRedhawk- .454.
I used mostly AFrames getting ready for the hunt. My friend, JD Jones gave me the devil for using AFrames. Their manufacturing process greatly increases chamber pressures. Sent it to Thompson. They'd seen very few stretched Encore frames. Sent me a new one!!
I don't use AFrames in my single shots. When used in revolvers I reduce the load a few grains.
 

Recent Posts

Top