Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Reloading
30-284?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Tac-O" data-source="post: 2199311" data-attributes="member: 109994"><p>I shot on Saturday for break and testing... It will definitely shoot if I can get the chambering/extraction issue resolved!!</p><p></p><p>I got tired of doing the cleaning/break in after about 7-8 rounds, so I used the remaining 5 I had loaded for that process (just a starting charge of 4451 and Hornady interlocks) and fired them pretty hastily to see what it would do and they were all within 3/4". That's with my cracked laminate stock and not taking my time to try to put them all in the same hole. So... Yea I'm confident it will do well since I got those crown burrs knocked off haha. I was frustrated at that point so I just wanted to shoot.</p><p></p><p>The the others I shot were loaded for load testing. 150gr Sierra flats. 5 groups of 3 charges. 3 of the loads had 2 touching and one about 1/2" off the group. The other 2 charges were right around 1" I think.</p><p></p><p>Looking at neck turning/reaming, if I DO have to start doing that, I was thinking these two pieces would work to turn the outside neck and cut off the donuts if they form.</p><p></p><p><a href="https://www.midwayusa.com/product/1017596030?pid=293609" target="_blank">Km neck turning rool</a></p><p><a href="https://www.midwayusa.com/product/6249283077?pid=989238" target="_blank">Km carbide cutting pilot</a></p><p></p><p>Would I need anything other than those two pieces? I see there is an expanding mandrel iron tool, but not sure I'd actually need that if I have a neck expander already. I think the mandrel on my Lyman expander is .3065 or something close</p></blockquote><p></p>
[QUOTE="Tac-O, post: 2199311, member: 109994"] I shot on Saturday for break and testing... It will definitely shoot if I can get the chambering/extraction issue resolved!! I got tired of doing the cleaning/break in after about 7-8 rounds, so I used the remaining 5 I had loaded for that process (just a starting charge of 4451 and Hornady interlocks) and fired them pretty hastily to see what it would do and they were all within 3/4". That's with my cracked laminate stock and not taking my time to try to put them all in the same hole. So... Yea I'm confident it will do well since I got those crown burrs knocked off haha. I was frustrated at that point so I just wanted to shoot. The the others I shot were loaded for load testing. 150gr Sierra flats. 5 groups of 3 charges. 3 of the loads had 2 touching and one about 1/2" off the group. The other 2 charges were right around 1" I think. Looking at neck turning/reaming, if I DO have to start doing that, I was thinking these two pieces would work to turn the outside neck and cut off the donuts if they form. [URL='https://www.midwayusa.com/product/1017596030?pid=293609']Km neck turning rool[/URL] [URL='https://www.midwayusa.com/product/6249283077?pid=989238']Km carbide cutting pilot[/URL] Would I need anything other than those two pieces? I see there is an expanding mandrel iron tool, but not sure I'd actually need that if I have a neck expander already. I think the mandrel on my Lyman expander is .3065 or something close [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Reloading
30-284?
Top