.280 Ack. Powders Vs. 30-06 Powders

Jcub

Well-Known Member
Joined
Aug 8, 2013
Messages
173
Why is it I rarely, if ever run across published loads used for 30-06 using Retumbo, H-1000 or other similarly slow burning powders like I do for the .280 Ackley? Yet they are the virtually the same case?
 
Why is it I rarely, if ever run across published loads used for 30-06 using Retumbo, H-1000 or other similarly slow burning powders like I do for the .280 Ackley? Yet they are the virtually the same case?

Good question. I've been wondering the very same thing. Don't want to hijack this thread but has anyone played with Retumbo in a 30-06. ?????
 
Why is it I rarely, if ever run across published loads used for 30-06 using Retumbo, H-1000 or other similarly slow burning powders like I do for the .280 Ackley? Yet they are the virtually the same case?

Because those slower burning powders are not as effective in the .06 case in most instances. But, Reloder 22 is a very good powder in the .06 with 180 and heavier gr bullets.
 
Because those slower burning powders are not as effective in the .06 case in most instances. But, Reloder 22 is a very good powder in the .06 with 180 and heavier gr bullets.
Bingo!! we have a winner!!

You can't put enough load (bullet weight) on some slow burning powders to get them to full pressure in a not so overbore round like the '06; it's all case capacity to bore diameter (with bullet weight thrown in). rl22 will make a 180 haul in an '06, and is probably the slowest powder I'd use in it.
 
Because those slower burning powders are not as effective in the .06 case in most instances. But, Reloder 22 is a very good powder in the .06 with 180 and heavier gr bullets.


But the .280 Ack IS the '06 case, with 4 more grains of powder. So you're saying that those 4 extra grains are the difference between Retumbo working or not?
 
But the .280 Ack IS the '06 case, with 4 more grains of powder. So you're saying that those 4 extra grains are the difference between Retumbo working or not?
The difference is the size of the hole in the barrel.

A 350 Chevy engine with a 12:1 compression ratio has a different requirement for fuel than a 350 Chevy engine with an 8:1 compression ratio.
 
But the .280 Ack IS the '06 case, with 4 more grains of powder. So you're saying that those 4 extra grains are the difference between Retumbo working or not?

It only takes SLIGHT differences in rifle calibers all using the same parent case to make a substantial difference. Here's a parallel: take your water hose and put the older spin on cap on it and tighten it down making the hole smaller. What happens? The same water spits out faster and flatter.

Take your question in the opposite direction. Compare the 30.06 and the 338-06. By your questioning, shouldn't H1000, and Retumbo work optimally in it? The answer is no, in fact, the powder burn rates get faster again.
 
It only takes SLIGHT differences in rifle calibers all using the same parent case to make a substantial difference. Here's a parallel: take your water hose and put the older spin on cap on it and tighten it down making the hole smaller. What happens? The same water spits out faster and flatter.

Take your question in the opposite direction. Compare the 30.06 and the 338-06. By your questioning, shouldn't H1000, and Retumbo work optimally in it? The answer is no, in fact, the powder burn rates get faster again.


Makes complete sense when you put it that way. Thank you Gentleman.
 
Warning! This thread is more than 11 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top