243 win, IMR 4451, RL 26 velocity results

Idaho Trecker

Well-Known Member
Joined
Apr 19, 2013
Messages
1,390
Location
North Idaho
Made some range time today and just thought I would put some of my findings out there for these newer powders. I was mostly concerned about finding my max pressure/velocity today and here is what I came up with. These were shot at 200 yards and 15 feet from the chrono (shooting chrony) to muzzle.

I was running a 24" barrel from a Sako 85 varmint and Vortex Viper HST 6-24.

I forgot to mention my bore and all bullets were coated with HBN

105 Hornady BTHP
RL 26
46 2952
47 3058
48 3117
49 3212

The primers looked good through the 49 grains but I had a faint extractor mark on the case head. I think there is room for more speed.
My downfall is the fact that my rifle has a 1:10 twist and I have not been able to stabilize 105 bthp or A max. I was hopeful that the bthp would stabilize since it doesnt say a 1:9 or faster required.

on to the 87 V Max and IMR 4451
43 3086
44 3177
45 3272
46 3299

At 200 yards the vertical distance from the first shot to second was 1 3/4 inch. From shot 2 to 3 there was 1/8" vertical and horizontal!!! and the last shot was actually another 1/4" lower than shot 2 vertically but 3 1/2 inches right (dont think it was me)

It looks like the 4451 is going to work great for my setup and with a .4 bc its not terrible for some paper punchin way out there.
 
Last edited:
Re: 243 win, IMR 4451, RL 26 Ladder/velocity results

So if I understand, you loaded 1 bullet with each weight of powder ? What does that tell you ?

For a ladder test, you try to pre-determine the best seating depth for your bullet, then load 5 each with each powder weight. Then shoot a 5 round group with each set, always using the same point of aim. Then you compare drop relative to point of aim and GROUP SIZE to determine which powder node looks promising. Take along some unrelated loads or factory ammo to get the bore fouled and into a stable condition prior to shooting test loads.

Something about your reloading data looks fishy. Max loads for the 105gr A max are listed at 2980fps on the Hodgdon reloading website (with 40.4gr of IMR 4451) while your 87gr Vmax loads seem a tad slow (43.8gr of 4451 giving 3342fps from a 24" barrel).

So somehow you are slow on the light bullet and fast on the heavy one ? And your max load is way over the posted limit for the Vmax ? And you have no group information so you have no idea which load is going to repeat well, regardless of how fast it is ?

I have been running a calculated 3200fps with a 95gr Berger hunting bullet, but that is with an AI chamber. I certainly would not expect that kind of speed with a 105gr. Be careful, don't get hurt and check if anything groups a **** near the ragged edge. Sometimes there is a high node that works out, but not all of the time. A very hot load that you develop in spring could cause serious problems in the middle of summer, or if you tweak the seating depth or use a different primer.
 
Re: 243 win, IMR 4451, RL 26 Ladder/velocity results

I guess my terminology is off I should have said just looking for max pressure with those powder/bullet combos while finding the least vertical. Once I found the node with the least vertical I will go back and load groups within that range. I'm just trying to put some personal experience out there with the new powders.
 
Re: 243 win, IMR 4451, RL 26 Ladder/velocity results

Least vertical drop = maximum velocity. The bullet is going to obey the laws of physics. But all that tells you is the limit of the system. It does not give you any other information regarding accuracy at all. Usually the best approach is to start with a mid weight load and work up and shoot for groups. One should find an accuracy node close to that point and the question is just whether there is another higher up. You discover the same information regarding maximum pressure following the other route, but you will get to the higher pressure end last and can choose not to shoot the highest loads if you start seeing pressure signs earlier. If you develop a hot load in summer, it should be fine at any other time of the year, but beware developing a hot load in spring or winter that you want to shoot year round.
 
I made that mistake once when I developed a load for 6mmAI and IMR 831 in winter at 30 degrees and touched one off at 85 degrees the next summer... needless to say the primer was blown. I know i'm not near summer temps yet but they are at the max temp (todays data taken at 67 degrees) I will be hunting in since I'm gone from may to October fighting fires and no time to shoot.
 
Old post warning......

IMR 4451 IN 243 Winchester. Sierra 85gr hpbt #1530.

Rifle- Remington 600 Mohawk. 18" bbl.

Rem brass, Redding fl bushing die, no expander. .270" bushing.

CCI Br2 primer . Flash hole uniformed. Temperature 40 degrees. No wind.

100 yards IMR 4451 -44.0 GR 5 shots = .905" The first shot from clean barrel opened group. Just measuring the 4 =.482"

IMR 4451 - 44.5grs = 5 shots -.733"

Col 2.640" Sizing only 1/2 of the necks with the bushing.

Fired 1 round of each at 45.0 & 45.5grs to look for pressure. Seen no pressure signs.

I don't see any less copper fouling with this powder? Very old factory barrel. Many rounds fired.

I worked up from 37.5grs. because of Hodgdons 90gr bullet data for safety. It was a long road , working up.
I suggest working up using the Hodgdons/Sierra 80 gr data. Do so at your own risk. Be safe.
20200127_092258.jpg
20200127_092258.jpg
 
Old post warning......

IMR 4451 IN 243 Winchester. Sierra 85gr hpbt #1530.

Rifle- Remington 600 Mohawk. 18" bbl.

Rem brass, Redding fl bushing die, no expander. .270" bushing.

CCI Br2 primer . Flash hole uniformed. Temperature 40 degrees. No wind.

100 yards IMR 4451 -44.0 GR 5 shots = .905" The first shot from clean barrel opened group. Just measuring the 4 =.482"

IMR 4451 - 44.5grs = 5 shots -.733"

Col 2.640" Sizing only 1/2 of the necks with the bushing.

Fired 1 round of each at 45.0 & 45.5grs to look for pressure. Seen no pressure signs.

I don't see any less copper fouling with this powder? Very old factory barrel. Many rounds fired.

I worked up from 37.5grs. because of Hodgdons 90gr bullet data for safety. It was a long road , working up.
I suggest working up using the Hodgdons/Sierra 80 gr data. Do so at your own risk. Be safe.
20200127_092258.jpg
View attachment 171986
That speeds a whirlwind that will reach out for 1000 yd but I just need 300 yd and a 1/4 moa out my 1942 out my Springfield with 4451 imr
 
Top