12ga,10ga,8ga,4ga FH;585HE/700HE, other Big Bores--

[hubel458]

Last picture above shows what can be with sabots. It was thought to
be 20ga size when we got picture, but it is a smaller
45cal caliber sabot with 30cal streamlined bullets in them.
This was set up by the poster 'edge' on Castbullets forum.

More info on the SPW sabots with 520 gr Lyman reworked and locked into
them. With 3.5" brass RMC in the NEF long barrel gun, going about 2500
they smash though 6" timber with Lyman tearing wood up. Also got the same
combo 2200 in 3.5" plastic. Lyman in sabot on the left in picture on
right is factory SPW.

Another setup using the largest diameter 58 Minie I have is this .590" in this
12ga real thick muzzleloading wadcup for steel shot. I chamferred the bottom of
Minie slug and wedged it in the cup. The cup comes real long and we cut it off.
That leaves perfect edge to roll crimp against. Dab of epoxy holds the Minie slug
in, so it works like a non-discarding sabot. This wad has is own seal and fairly
short compared to others, so it leaves room for more of our slower powders.
Shorter slug and wad setups make loading easier.

Here is picture of the Magtech we redid in the 585HE by mono-blocking in 585
barrel. This is second one we've done. Tried out a ladder peep sight on the
back. Makes a neat gun.That underlever is a great touch.Ed

As part of the 585 test guns have smooth barrels, they are like a hopped up
24ga. We got couple bags of 24ga cards and felt wads. Easy way to use
reduced loads as the wads are perfect in 585 case. For comparison top load
say with RE17 and 650gr bullet is 170gr, but you can put in 100gr and card
and couple wads and have real easy load. And you don't have to worry about
airspace. Great for reduced loads with Minie slugs. In the same vein you
can put in a card over the powder and about 3/4 oz of shot and have a real
speedy 24ga shot load equivalent. Put card over the shot and glue it in.Ed

 

[hubel458]

First picture is of nice finished 87 Winchester Will Sanders got set up
and he is using short brass cases.Beautiful scroll work on the stock.

Next is takeoff of a slug idea from Longbow on Cast Boolits, 12ga lead
roundball with section of copper tube, with wads inside, bpgs seal on the
bottom, screwed together. I have many boxes of wads. Now he did his with
screw into ball, put tube on with screw centered inside tube and filled tube
with hot glue. It stays together. Both are nose heavy for smooth bore work.

Next is side sectioned view, one of our 585HE cases, showing how 3/4
ounce of shot fits in.. 585 is same bore as 24ga. Cards shown are 24ga.
Just glue top card in.Some of our 585s are smoothbore and the HB Minie
slugs work at short range and the shot will do at short range also going
over 2000 fps. Could use 24ga shotcup.

Next is a Mossy 390 with heavy 585 barrel. Makes a nice big bore gun,
and handles nice with texturized stock finish. About same strength as
the heavy break actions I have 585HE in.Ed

 

[hubel458]

Here is picture of the 12ga short brass RMC cases being used in
the 1887 WIN shown above. They are 2 5/8" long cases and we
get 600gr over 1900. He had work done on action to get it to feed
these and 3" roll crimped plastic. Brass loaded about same length
as 3' plastic crimped little long.

Next pic are Lyman slugs cast for thin 12ga wad, used in thickwall
10ga VP100 wads. These Lymans I got are on large size and fit
VP100 fairly well. Makes easy, lighter, superfast load in 10ga.

Next; further idea with Longbow's tube/roundball slug shown above.
Use tube hot glued to ball with screw in the back and use it in
a 10ga VP100 wadcup. These type slugs little more accurate used
in wads as opposed to fullbore.

Next shows picture of a long 585 bullets, about 1600gr in our 585HE
cases. Got the idea from Bret In Minn that could setup 585HE
guns with super long throat and load down to subsonic speeds to
make the 585HE Whisper.....And regular bullet loads would still fire
in the same guns......And at subsonic 1050fps it would have about
4000 ft lbs, about twice what the peashooter whisper cases have.
And my case could get a 2400 gr long bullet to same subsonic speed
for 6000 ft lbs. And one that long would have proportions like the
newer tank cannon, smooth barrel saboted darts, that it could be
possibly be done, using long 2400gr in smooth barrel.
Neat ideas from guys interested in whisper type loads.

Last is picture of FBW in our 585HE with handgrip stock and light
barrel for lightweight carrying. Grip is weighted, gun is 6lbs.
Barrel is 28". I'm not a fan of light barrels. 650gr at 2500 is max of
what I can hold onto shooting from the hip Moderate load
.Little info about my 585 loads, like in the break actions and the
Mossy in post above. I load about 85% max velocities, but to get
85% we only need 2/3 the peak pressure, like 40,000 psi
instead of 65,000...Ed

 

[hubel458]

We have a winner it seems. The 12ga sabots using 58cal slugs.

The sample 12ga sabots got here earlier this week. And we got a bunch
of testing already for opening and sealing, and some accuracy testing .440gr
Minie bullet, measuring .575"; with OD of sabot with slug in it of .737" It is
perfect. Going moderate 1800. Petals opened perfect and evenly and they all
stayed on perfect. No petals twisted or torn. Tested in 3" case with slower
powder loads. 80gr of 4759 and 50gr Alliant Steel. Fiocchi case.
Savage 210 rifled barrel, 1 to 35 twist. Cases with slower powders expanded
only a little, and those cases are soft ones.
We have big bunch of the sabots here now.

All petals were opened at about 30 deg to the base when picked up.
With ither powder the bases have no damage, or burn throughs or melting.
Took rifling perfect, so skidding on the rifling. Most of the rifling grip is on the
bottom half of sabot, which is why these and Accutips are best as the bottom
is full size instead of dropping back in size, compared to the top, like many
other sabots. Rifling in the barrel still clean..

The Minies are hollow based and the slug edges did not cut into the inside of the
sabot bases,just a slight impression. We have got good base thickness.
Good Accuracy - In the cold and very windy day, hit milk jugs at 30 yds.
Here is picture inside sabot showing just a slight indent. No need of cards under
slugs, and if you did, the the slugs would set up in sabot and not have the
curve of the slug behind the inside circular rib for best fit...

You got to use right powders. With right slower powders( not fast shotgun),
that start easier and used in larger amounts, you won't tear up the sabots.
It is false economy to use all fast shotgun powders,trying to get twice as many
shots per pound... and tear up sabots, expand cases too much, get poor groups,
miss that deer or whatever. For most of you in 3" cases Alliant Steel is best.

Get with me for cases -- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included, or $20 for 50 postage included,
with a bonus WE WILL send along 10 slugs with 100 order, 5 with 50 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr..Ed

 

[hubel458]

Here is picture of a bunch of the sabots with different slugs and bullets.
Back Row- Two roundball load, balls 285gr each-- pointed long 700 gr -- a blunt
solid 700gr-- tungsten slug 1000gr --- jacketed bullet -- 600gr.
2nd row-611 Lyman 530gr Minie- 500gr flat base- Lee 500gr hard--Lee 500gr soft
1st Row- Lyman 440gr old style minie-- Lyman 510 gr new style-- 440gr from Dixie
Gunworks-- 400gr Lee target style. I like 440gr old style and 440 gr Dixie. For sale
on Gunbroker is all sizes and weights.. Or cast your own. Lots of moulds around.
Lee moulds only 20 bucks. Best diameters to use are .574 " to .577" Minies.
If you have ones bigger and they are not hardened you can roll them betweem two
hard surfaces and they will get little smaller. I have some that are .585" 440gr
and work in my 585HE and they can be rolled smaller.

Here are sabots with variety of seals/wads, and the shortest one in picture with
white felt wad just fits in 3" case with 80gr 4759, and still leaves room to roll crimp.
I compress it in hard. Now only faster powder than 4759 I'd use is Alliant Steel in
smaller amounts, 50gr Steel, in 3", and thicker wads and cushions like shown.
To roll crimp over the top edge of sabot we had .220" of case before crimping.
You only have to crimp top edge of sabot real good.

After crimping the slugs are tight and don't move around. The circular rib inside the
sabot holds slugs tight back into the base. Speeds over 2000 fps
will be gotten using 3.5" plastic cases, with our slower powder loads. .
More testing for accuracy yesterday, a warmer, calmer day, with steel sights.
Hit. paper plate at 50 yds.

As said above, best to use right powders. Right slower powders( not fast shotgun),
that get to peak pressure slower, thus can use larger amounts, can get to higher
velocities, and you won't tear up the sabots and won't expand cases as much.

For most of you in 2.75" and 3" cases Alliant Steel is best.
FOR 440GR SLUGS IN SABOT---For 2.75" start at 40gr and go up to about 50.
For 3" start at 45gr go up to about 55. I like 3.5" best as you can load much easier
for speed, still have more cushion wads. Start with 50gr Steel, go up to about 62.
Case brands act different, but using the slower powders minimizes the differences
and keeps us away from surprizing pressure problems.

In 3" plastic,most 4759 I can get in and still have 1/4"cushion is 80gr.... In the 3.5"
I can get in 105 gr with this sabot and get over 2000 fps, In these loads if using
480-500gr cut back 3 gr. These 58cal slugs can be cast or they are at Dixie Gunworks
and 4 guys on Gunbroker got them. Get ones .574" to .577"


Interested in sabots--- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included.
Or $20 for 50 postage included..
.Or 150 for $45 postage included----- ALL with a bonus
WE WILL send along 10 slugs with 100 order, 5 with 50 order. 15 with 150 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr..
We want you to help test and find what is best....Ed

 

[hubel458]

Here is picture of 45-50yd target, used a scoped NEF Ultra, the sabot load of a 440gr
58cal slug in it at 1800... Measures 2.5" on outside for 3 shots.

Here is pic of almost 2100 of them. More coming. Time to
get them and get loads working.

A little levity in this process.Ed

 

[hubel458]

Some more info about our sabots and various slug weights......
First and most important is our sabots fitting real tight like the Accutip
Sabots, they will not get the same speed at the same pressures as
the undersize grey and blue ones, But they do leave the barrel
headed straighter and without damage, even with hollowbase 58cal
slugs in them as the pics above show. No cards under slugs in sabots.,
But with good powder seals, using Alliant Steel, and good 1/4" minimum
cushion wads.

The 440gr Minie slug of .575" in the 3" cases is the one I used as a
base loading, to work each way by weight to find what loads of
Alliant Steel work and extract in my NEF. Using 3" soft base cases.
Here is pic of before/after of Fiocchi cases, on right unfired and left
fired, 55gr Steel with 440 gr slug.

For 440gr max of 55gr Steel
For 400gr max of 57gr Steel
For 360gr max of 59gr Steel

For 490gr max of 52gr Steel.
For 510gr max of 49gr Steel
For 540gr max of 47gr Steel.

I tested all these weights for extraction. It is real nice to reach into a
bucket, grap a sabot that fits right, and go to loading and shooting.
Many of you need to get in on the fun.
Here is picture of Fiocchi with sabot, roll crimped. The top of sabot is
perfect for roll crimping...It is setting under crimp tool in drill press.

Earler I showed the 585HE Falling block with pistol grip and the light
barrel. Here it is with Knoxx Compstock buttstock. We added 2 extra
springs inside for relatively hard recoiling gun, as stock originally made
for a REM 870 Pump. Works great and looks nice; will putting one on
the Magtech 585HE singleshot break action and got one in rifle stock
for Ruger 77 in 585HE.

And many guys want wildcats with shoulders, with big neck down, so
in developing the ultimate 700 blaster, here is the 700HSM. Shown next
to Gibbs 650gr ball powder..1000gr at 3800...How about that.
Will be one of only 2 guns I plan on being over 30 lbs, other is 2bore..
Whoppee.....Ed

 

[hubel458]

950 sabots of the 10,000 gone in 10 days. Time to get them.

AND TEST THEM and let us know how they do. It would be

great if they are as good as the good factory sabots,

and we get them tested and figured out before next deer

and hog seasons.

Two ways it could work out---A Little humor--

1) If they are good they will be Hubel Sabots- 2) if bad, **** Hubel Sabots--

I have set it up so they can be paid through PayPal if you want..
100 $33--150 $45-- 200 $57-- Every extra 50 $12.
Contact info above.Ed

PS- I make nothing on these I have 2500 in them the last
year or so and I'll get 31-3300 and with postage, paypal
fees,etc of 6-800 we are about even. I just want
to get a good sabot out there.

 

[hubel458]

The sabots aren't moving fast at all and I got to
money back out of them right way, and seeing as how
we're low on slugs to send with the sabots, in big numbers,
and no one has yet to buy out our stash of sabots and
set up so they can be selling the sabots, so we will try
selling them fast a few weeks longer. So to get these
moving out and getting tested and we pay our bills,we will
be having sale on just the sabots, in larger amounts only.
We will send one each of 440gr and 500gr slug so
the guys can see what we have found that works.

Because of the shipping costs and boxes that 2, 3, or 4 bags
of sabots fit in, that has an affordable postage cost to pay,
we have to sell these in 200, 300, and 400 size orders..
So, 200 sabots $47 Shipping included,
300 sabots $65 Shipping included...400 for $83 shipping incl.

Now 200 of the other brand X of undersize ones cost $68
plus shipping. There was dozens of guys the last few
years all over the internet that bought undersize junk,
that wanted good sabots and complained that the ones
they bought elsewhere didn't work...... I haven't heard
from most of them, So guys see if you got time, please
help us out here..MO, Check, Paypal..Ed

 

[hubel458]

The sabots work in brass cases .First is sabot in a Magtech brass case,
next to 3" plastic.. In shorter brass it would hold about as much powder
as in longer plastic if loaded like in the picture..
Sabots are about .734-735" with slugs in them, and
the Magtech brass with its thin sides still is slightly small OD at the
top compared to plastic, with sabot wedged in.

Next is sabot in RMC case, and sides are full thickness like plastic cases
at the mouth, so don't expand case to hold sabot. We have RMC make case
mouth ID to fit sabot. Sabot being little over fits barrels tight and rifling
impresses into plastic well and gets best spin, and being tight it leaves barrel
straight, with petals opening evenly. Brass case mouths are tight enough that
we push sabot in with a press.Saves trying to crimp heavy RMC case.

Here is picture of a barrel and barrel on a gun from 20 gauge singlshots that
will have the heavy 20ga rifled barrel in picture, mono-blocked into them.

 

[hubel458]

We've sold 3400 sabots in 5-6 weeks, 6600 left here.
They can make more. Hooray it's picking up a little.
Get them while they are hot, so to speak.

These are 12ga sabots taking 58cal slugs.
These slugs are real devastating. Use the ones with
diameters of .574" to .577". Nothing bigger diameter is needed.
You can cast your own OR--

58cal slugs for these can be bought at Dixie Gunworks.
Item Numbers-- BA 1103 48.50 per 100
and BU 0901 52.50 per 100

There are 3 guys selling the right diameter ones on Gunbroker.
Their names on there are --
Blue Falcon --who has 3 or 4 that will fit.
Maplewoodbullets-- who has 2 weights in old style Lyman in one listing.
peoprepofkal-- has old style lyman in 490g

All of these are 40-50cents each.Ed

 

[hubel458]

What causes sabot problems/inaccuracy. Some pictures will help.
First 2 shows a skinny post that pushes on a cushion or sabot
bottom and it can bend or deflect which if that way when exiting
barrel can start sabot or slug crooked.

And more important item that can cause lack of accuracy is if
base of discarding sabot tapers or steps down so that it isn't real
tight as it leaves bore, which can allow it to be cocked.
On the left is our sabot which has base right and other brand
which tapers a bit. Easy to see.

Next is a ball and slug load in 2 of our sabots. A 285gr .575" ball
flattened, put in the bottom and 400gr Minie above, two different
styles of Minies.

Here is couple 16ga discarding sabots I made from the undersize
12ga grey ones. Didn't have to take off much. Much better use
for them. I made them, after Paul in Alaska asked about
where to find 16ga ones, to see what they looked like.
They still use 50cal slug.. Ed

 

[hubel458]

Here is 16ga discarding sabots made from grey ones with other 16ga slugs..
20 ga factory sabot on left for comparison.

Here is picture of 12ga wads showing good and bad support.

Here are 2 sabots on the right with super heavy tungsten slug. It is 1100gr,
but tungsten costs ten times what lead costs.

Here is a sabot home defense or close range defense load setup using our
sabot. It has five flattened 45cal balls in it. Flattened into a fat disc weighing
145gr each. You'd star crimp it or use card over them and roll crimp. Like
having a bunch of supersize flat buckshot, only super big.

Here is comparison picture of the 58cal slugs used in our 12ga sabots, with the
puny slugs used in many other sabots. And we've moved 5500 of the sabots.
Deer season is coming fast. Maybe time to get loads tested/sighted in is now.

Some more figures. The 24hr Campfire forums is first one, with our 12ga FH thread,
to get over half million thread views.The HighRoad second.
TheFiringLine third. AR fourth...Ed

 

[hubel458]

We have moved few thousand sabots.More here.
Here is picture of an 8ga wad with tube slug in it, we made.

A pallet load of our 585HE cases has arrived in the US
and will be here in little while. And should be another pallet
of them this fall. Here is picture of our 585
with the solid turned CEB bullets in them.

Here is some helpful, simple math to help figure out the kinetic energy
of your loads, just by having bullet weight and speed.
Just put these multipliers which are used for each speed, on a list
and multiply by the bullet weight in grains. Fast and easy.Ed

Speed..Multiplier
1500------5
1600------5.7
1700------6.42
1800------7.2
1900------8
2000------9
2100------9.8
2200------10.75
2300------11.75
2400------12.8
2500------13.9
2600------15
2700------16.2
2800------17.4
2900------18.7
3000------20