Brass is hard to chamber after full-length resize

MT6.5PRC said:

I'm reloading 6.5 PRC Hornady brass. Factory ammo chambers fine. After resizing the brass using a Hornady match full-length resize die, the brass barely chambers—the bolt is sticky loading and unloading the brass. I have the die set so the case goes as far into the die as possible (shell holder hits the bottom of the die and cams over). Hornady customer services says it's because the match-grade dies only bump the shoulder .002" and the custom dies will bump the shoulder farther back.

Does anyone know if this is true? Let's be honest, there's a ton of misinformation in the guns/ammo/reloading world, and I've learned not to trust something just because someone who should know what they're talking about says it (because a lot of them don't actually know, even though they should).

Seems to me that bumping the shoulder even .002" should be enough for it chamber without the bolt getting sticky. I'm suspicious that the resizing die I got is out-of-spec (happened before w/ a Hornady .308 custom die and the problem resolved when I got a .308 match die).

Should I just get another resizing die, this time not a Hornady, and see if that fixes the issue? Dillon doesn't make 6.5 PRC dies yet, so I'd have to get Forster, RCBS, or Redding. Recommendations on which one to get?

Click to expand...

MT6.5PRC said:

I'm reloading 6.5 PRC Hornady brass. Factory ammo chambers fine. After resizing the brass using a Hornady match full-length resize die, the brass barely chambers—the bolt is sticky loading and unloading the brass. I have the die set so the case goes as far into the die as possible (shell holder hits the bottom of the die and cams over). Hornady customer services says it's because the match-grade dies only bump the shoulder .002" and the custom dies will bump the shoulder farther back.

Does anyone know if this is true? Let's be honest, there's a ton of misinformation in the guns/ammo/reloading world, and I've learned not to trust something just because someone who should know what they're talking about says it (because a lot of them don't actually know, even though they should).

Seems to me that bumping the shoulder even .002" should be enough for it chamber without the bolt getting sticky. I'm suspicious that the resizing die I got is out-of-spec (happened before w/ a Hornady .308 custom die and the problem resolved when I got a .308 match die).

Should I just get another resizing die, this time not a Hornady, and see if that fixes the issue? Dillon doesn't make 6.5 PRC dies yet, so I'd have to get Forster, RCBS, or Redding. Recommendations on which one to get?

Click to expand...

MT6.5PRC said:

I'm reloading 6.5 PRC Hornady brass. Factory ammo chambers fine. After resizing the brass using a Hornady match full-length resize die, the brass barely chambers—the bolt is sticky loading and unloading the brass. I have the die set so the case goes as far into the die as possible (shell holder hits the bottom of the die and cams over). Hornady customer services says it's because the match-grade dies only bump the shoulder .002" and the custom dies will bump the shoulder farther back.

Does anyone know if this is true? Let's be honest, there's a ton of misinformation in the guns/ammo/reloading world, and I've learned not to trust something just because someone who should know what they're talking about says it (because a lot of them don't actually know, even though they should).

Seems to me that bumping the shoulder even .002" should be enough for it chamber without the bolt getting sticky. I'm suspicious that the resizing die I got is out-of-spec (happened before w/ a Hornady .308 custom die and the problem resolved when I got a .308 match die).

Should I just get another resizing die, this time not a Hornady, and see if that fixes the issue? Dillon doesn't make 6.5 PRC dies yet, so I'd have to get Forster, RCBS, or Redding. Recommendations on which one to get?

Click to expand...

Mikecr said:

I doubt it's a chamber too tight. That fired cases expanded 2thou near webs, at least, tells me you have plenty of clearance.
Opening the chamber further will just allow even more growth & kill case life.

If near webs are left in interference fit with the chamber then you likely have weak breech support for the cartridge & load.
If your die doesn't counter that, then the die may be right -but no good for you.
Personally, I'd have a custom die made from fired cases.

Click to expand...

MT6.5PRC said:

I'm reloading 6.5 PRC Hornady brass. Factory ammo chambers fine. After resizing the brass using a Hornady match full-length resize die, the brass barely chambers—the bolt is sticky loading and unloading the brass. I have the die set so the case goes as far into the die as possible (shell holder hits the bottom of the die and cams over). Hornady customer services says it's because the match-grade dies only bump the shoulder .002" and the custom dies will bump the shoulder farther back.

Does anyone know if this is true? Let's be honest, there's a ton of misinformation in the guns/ammo/reloading world, and I've learned not to trust something just because someone who should know what they're talking about says it (because a lot of them don't actually know, even though they should).

Seems to me that bumping the shoulder even .002" should be enough for it chamber without the bolt getting sticky. I'm suspicious that the resizing die I got is out-of-spec (happened before w/ a Hornady .308 custom die and the problem resolved when I got a .308 match die).

Should I just get another resizing die, this time not a Hornady, and see if that fixes the issue? Dillon doesn't make 6.5 PRC dies yet, so I'd have to get Forster, RCBS, or Redding. Recommendations on which one to get?

Click to expand...