Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
What do ya'll think about a 6.5-375 Ruger?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Kingfisher" data-source="post: 478776" data-attributes="member: 31627"><p>I've been a lurker of this board for years but never registered an account (thought I had but apparently not). A friend of mine mentioned this thread so I thought I'd finally sign up and weigh in.</p><p> </p><p>I've been plotting a 6.5/375 Ruger for a couple of years now. I'm finally going to kick off the project in the next month. Fortunately for me I was able to connect with another fellow who had already built one and the gentlemen was so nice that he even loaned me the reamer. Aside from being throated a bit short, which my gunsmith can rectify the reamer is cut exactly to the dimensions I was looking for. The accuracy out of his rig has been very good, with velocities around 3300 fps. for 140's. That's exactly the kind of performance I'm looking for.</p><p> </p><p>Now here's the downsides. The dies are going to be custom. Redding has a few of them in stock, but the full kit for everything you need is going to run you $200+ for the dies and that doesn't even include the case forming component. I'm going to use 338 RCM and 300 RCM dies to size the 375 case down progressively before the final pass through a 6.5/375 Redding die. The next problem with taking the case down this far is that the necks end up pretty darn thick. You're going to have to neck turn and/or neck ream. A lot of work. You could have the reamer cut to account for the thick necks, but IMHO you're going to end up with less than desirable results. I've sized 378 Wby cases down to 30/378 before, so I think if you were just going down to 300/375 Ruger you wouldn't have this problem, but if you're going on down to 264 you can probably bank on it. With the IRS savings account aka tax refund now in hand, I'll be ordering a Lilja barrel tomorrow. Next up is the Stiller action, and so on.</p><p> </p><p>Anyway, I hope some of that is helpful. I think the performance will ultimately worth it, but it's going to be a PITA. I'm under no illusions about that part. For the OP, good luck with your project. I'll try to throw down some updates as my own project progresses.</p></blockquote><p></p>
[QUOTE="Kingfisher, post: 478776, member: 31627"] I've been a lurker of this board for years but never registered an account (thought I had but apparently not). A friend of mine mentioned this thread so I thought I'd finally sign up and weigh in. I've been plotting a 6.5/375 Ruger for a couple of years now. I'm finally going to kick off the project in the next month. Fortunately for me I was able to connect with another fellow who had already built one and the gentlemen was so nice that he even loaned me the reamer. Aside from being throated a bit short, which my gunsmith can rectify the reamer is cut exactly to the dimensions I was looking for. The accuracy out of his rig has been very good, with velocities around 3300 fps. for 140's. That's exactly the kind of performance I'm looking for. Now here's the downsides. The dies are going to be custom. Redding has a few of them in stock, but the full kit for everything you need is going to run you $200+ for the dies and that doesn't even include the case forming component. I'm going to use 338 RCM and 300 RCM dies to size the 375 case down progressively before the final pass through a 6.5/375 Redding die. The next problem with taking the case down this far is that the necks end up pretty darn thick. You're going to have to neck turn and/or neck ream. A lot of work. You could have the reamer cut to account for the thick necks, but IMHO you're going to end up with less than desirable results. I've sized 378 Wby cases down to 30/378 before, so I think if you were just going down to 300/375 Ruger you wouldn't have this problem, but if you're going on down to 264 you can probably bank on it. With the IRS savings account aka tax refund now in hand, I'll be ordering a Lilja barrel tomorrow. Next up is the Stiller action, and so on. Anyway, I hope some of that is helpful. I think the performance will ultimately worth it, but it's going to be a PITA. I'm under no illusions about that part. For the OP, good luck with your project. I'll try to throw down some updates as my own project progresses. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
What do ya'll think about a 6.5-375 Ruger?
Top