Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Long Range Scopes and Other Optics
New guy advice: 700 RUM weaver style hunting setup-which one?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Michael Eichele" data-source="post: 273975" data-attributes="member: 1007"><p>Since most of the hunting I do requires me to carry my rifles often times for 12 hours a day for days on end, I prefer to keep the mounting system light. I didnt say weak, just light in weight. </p><p></p><p>I start with the Nightforce 2 peice 20 MOA base. I find it easier and cleaner to get perfect alignment with a 2 peice than a one peice. Logic says otherwise but I find it easier. Then after I install the bases PROPERLY, I install the Night force UL rings. Both rings weigh less than one badger ring.</p><p></p><p>Properly installing a one peice base requires JB weld or similar. I hate dealing with them mess and the one piece bases are much heavier.</p><p></p><p>A two piece can be installed and made to be aligned in a few moments with a single cut file. This ensures very precise ring alignment. After the top two bases are aligned with eachother, then I loosen the back base a wee bit, just enough to move around with minimal effort. Then I set the ring in the forward slot of the rear base and tighten it down. I install a 30mm alignment bar in the rings, snug them down and then tighten the back screw of the rear base. This ensures proper side to side alignment. After this, I take of the half moons and set the alignment bar aside and use the 2 pointed bars to make absolutly certain the rings are perfectly aligned. After verification, I start installing the scope.</p><p></p><p>Which ever type you decide to go with, make sure you take the time to align the rings. This prevents damage and can help prevent ring marks to your scope. Using aluminum rings, they are typically in very smooth shape and wont leave marks UNLESS the rings are not perfectly aligned. Steel rings ussually need to be lapped to make them smooth enough so they dont leave any marks. Again, if they dont line up, they will still leave marks.</p><p></p><p>One piece or two peice, it will take effort to get perfect ring alignment. The problem ussually isnt with the base(s) rather with the action. A one peice may be straight when you recieve it but not after you torque it to the action. This is where JB weld come to play. You tighten the front part down and not the back. JB fills the void under the back so after it is dry, you can torque it down and she stays straight. Dont forget the releasing agent.</p></blockquote><p></p>
[QUOTE="Michael Eichele, post: 273975, member: 1007"] Since most of the hunting I do requires me to carry my rifles often times for 12 hours a day for days on end, I prefer to keep the mounting system light. I didnt say weak, just light in weight. I start with the Nightforce 2 peice 20 MOA base. I find it easier and cleaner to get perfect alignment with a 2 peice than a one peice. Logic says otherwise but I find it easier. Then after I install the bases PROPERLY, I install the Night force UL rings. Both rings weigh less than one badger ring. Properly installing a one peice base requires JB weld or similar. I hate dealing with them mess and the one piece bases are much heavier. A two piece can be installed and made to be aligned in a few moments with a single cut file. This ensures very precise ring alignment. After the top two bases are aligned with eachother, then I loosen the back base a wee bit, just enough to move around with minimal effort. Then I set the ring in the forward slot of the rear base and tighten it down. I install a 30mm alignment bar in the rings, snug them down and then tighten the back screw of the rear base. This ensures proper side to side alignment. After this, I take of the half moons and set the alignment bar aside and use the 2 pointed bars to make absolutly certain the rings are perfectly aligned. After verification, I start installing the scope. Which ever type you decide to go with, make sure you take the time to align the rings. This prevents damage and can help prevent ring marks to your scope. Using aluminum rings, they are typically in very smooth shape and wont leave marks UNLESS the rings are not perfectly aligned. Steel rings ussually need to be lapped to make them smooth enough so they dont leave any marks. Again, if they dont line up, they will still leave marks. One piece or two peice, it will take effort to get perfect ring alignment. The problem ussually isnt with the base(s) rather with the action. A one peice may be straight when you recieve it but not after you torque it to the action. This is where JB weld come to play. You tighten the front part down and not the back. JB fills the void under the back so after it is dry, you can torque it down and she stays straight. Dont forget the releasing agent. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Long Range Scopes and Other Optics
New guy advice: 700 RUM weaver style hunting setup-which one?
Top