Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Is barrel break-in really needed for factory guns?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="brian b" data-source="post: 59370" data-attributes="member: 2797"><p>[ QUOTE ]</p><p>I would suggest you listen to yourself and your intuition.</p><p></p><p>Barrel break in is full of urban legend that getting a clear answer is a big waste of time.</p><p></p><p>Mechanically, all that is being done is to remove any rough spots. Whether it is with a bullet or lapping compound really doesn't matter. </p><p></p><p>The most recent rifle I have is a Savage 110 in 270. Rds 4,5, and 6 went into 1/4". All I did before firing was to clean out the oil in the bore. I would suggest barrel is broken in.</p><p></p><p>Personally, I don't bother with barrel break in. I just shoot and see what happens. If accuracy degrades quickly, then I hand polish with some JB bore polish and non embedding compound. This just takes the 'edge' off the lands. About as gritty as toothpaste so removing metal would take a lifetime.</p><p></p><p>A bit more shooting and a barrel will settle down, IF it is ever going to. A mis manufactured barrel is never going to improve. A well made barrel will shoot from the get go.</p><p></p><p>I really don't see the point of breaking in a match barrel. If this is a quality lapped barrel, any thing I do is only going to degrade the finish and cause wear. I would just shoot it as is. If a match barrel looses accuracy quickly due to fouling, I got a lemon and its back to the shop.</p><p></p><p>My 2 cents..</p><p></p><p>Jerry </p><p></p><p>[/ QUOTE ]</p><p> This is the biggest crock I have ever read on this forum ,I tried not to respond but I can not let this pass.</p><p> If you have ever really done a barrel break-in correctly then this quote is absurd.</p><p> Every barrel manufacturer on the planet suggests a barrel break -in, it is more than just smoothing out the rough edges it is just like seasoning a new dutch-oven, dont do it and things dont turn out quite as well.</p><p> Doing a barrel brake-in makes your barrel copper foul less and clean up easier for the life of the barrel with better accuracy.</p><p> I have tested guns over the years on doing break-in or not ,I will never NOT break-in again factory or custom.</p><p>B</p></blockquote><p></p>
[QUOTE="brian b, post: 59370, member: 2797"] [ QUOTE ] I would suggest you listen to yourself and your intuition. Barrel break in is full of urban legend that getting a clear answer is a big waste of time. Mechanically, all that is being done is to remove any rough spots. Whether it is with a bullet or lapping compound really doesn't matter. The most recent rifle I have is a Savage 110 in 270. Rds 4,5, and 6 went into 1/4". All I did before firing was to clean out the oil in the bore. I would suggest barrel is broken in. Personally, I don't bother with barrel break in. I just shoot and see what happens. If accuracy degrades quickly, then I hand polish with some JB bore polish and non embedding compound. This just takes the 'edge' off the lands. About as gritty as toothpaste so removing metal would take a lifetime. A bit more shooting and a barrel will settle down, IF it is ever going to. A mis manufactured barrel is never going to improve. A well made barrel will shoot from the get go. I really don't see the point of breaking in a match barrel. If this is a quality lapped barrel, any thing I do is only going to degrade the finish and cause wear. I would just shoot it as is. If a match barrel looses accuracy quickly due to fouling, I got a lemon and its back to the shop. My 2 cents.. Jerry [/ QUOTE ] This is the biggest crock I have ever read on this forum ,I tried not to respond but I can not let this pass. If you have ever really done a barrel break-in correctly then this quote is absurd. Every barrel manufacturer on the planet suggests a barrel break -in, it is more than just smoothing out the rough edges it is just like seasoning a new dutch-oven, dont do it and things dont turn out quite as well. Doing a barrel brake-in makes your barrel copper foul less and clean up easier for the life of the barrel with better accuracy. I have tested guns over the years on doing break-in or not ,I will never NOT break-in again factory or custom. B [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Rifles, Bullets, Barrels & Ballistics
Is barrel break-in really needed for factory guns?
Top