Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Gunsmithing
Homemade fibreglass stock
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="kiwi3006" data-source="post: 404405" data-attributes="member: 8927"><p>406pat. Make both halves of the stock at the same time. Once the fibreglass has started to set you can trim the halves with scissors, although I left it to the next morning and used a hacksaw blade. </p><p>Leave the halves in the mold and bolt the two halves of the mold together. You need to do this within 24 hours or so of moulding the hlaes so that the strips of cloth will chemically bond to the two halves.Cut some thin strips of cloth and coat them in resin. I used a squeege to spread the resin. Then put the cloth over the seams. I used three layers of cloth.</p><p> </p><p>I made the molds so that I could get acess to the forearm and action area while the molds were bolted together. I also left the end of the butt open for the same reason. The pistol grip area is the tricky area. You have to get at it through the action. I bent some wire so that I could push the cloth down on to the seam. Have a dry run with dry cloth before you do it.</p><p> </p><p>With the forarm I used polystyrene to fill out the area, then cloth and resin over top.</p><p> </p><p>For the action area I had made a two part cast of the action using silicon sealant. Then I sat the cast in the apropriate place and poured resin with 403 filler around it. I made a dam so that it didn't run back into the pistol grip. </p><p> </p><p>I moulded the bolt cutout into the stock so that I could use it as a key for locating the action cast. I did the same with the floorplate cutout. </p><p> </p><p>Stu.</p></blockquote><p></p>
[QUOTE="kiwi3006, post: 404405, member: 8927"] 406pat. Make both halves of the stock at the same time. Once the fibreglass has started to set you can trim the halves with scissors, although I left it to the next morning and used a hacksaw blade. Leave the halves in the mold and bolt the two halves of the mold together. You need to do this within 24 hours or so of moulding the hlaes so that the strips of cloth will chemically bond to the two halves.Cut some thin strips of cloth and coat them in resin. I used a squeege to spread the resin. Then put the cloth over the seams. I used three layers of cloth. I made the molds so that I could get acess to the forearm and action area while the molds were bolted together. I also left the end of the butt open for the same reason. The pistol grip area is the tricky area. You have to get at it through the action. I bent some wire so that I could push the cloth down on to the seam. Have a dry run with dry cloth before you do it. With the forarm I used polystyrene to fill out the area, then cloth and resin over top. For the action area I had made a two part cast of the action using silicon sealant. Then I sat the cast in the apropriate place and poured resin with 403 filler around it. I made a dam so that it didn't run back into the pistol grip. I moulded the bolt cutout into the stock so that I could use it as a key for locating the action cast. I did the same with the floorplate cutout. Stu. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Gunsmithing
Homemade fibreglass stock
Top