Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Reloading
Help! Baffled by High Pressure Signs
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="azsugarbear" data-source="post: 538100" data-attributes="member: 4809"><p>I have a semi-custom 243 Win. that is built on a Rem Model 7 action. It wears a Brux fluted barrel chambered in PTG's 243 Tactical Match with a 1 in 9 twist. Action is bedded in HS stock. Leupold 4-14x40 scope.</p><p></p><p>At this point, I should probably mention that I have been reloading for 25+ years. During break in of barrel, I loaded and tried several different powders in my Lapua brass. I shot the following ladders with the 105 gr. Berger VLD:</p><p></p><p>H4831sc - 40.0 to 44.0 grains* (settled on 42.5 gr. @ 2,860 ave. fps)</p><p>H1000 - 43.0 to 46.5 grains* (settled on 45.0 gr.)</p><p>H4350 - 37.0 to 41.0 grains* (settled on 41.0 gr. @ 2,930 ave. fps)</p><p></p><p>* all loads are within min and max load range recommended by Berger</p><p></p><p>Shot drop chart w/41 gr. of H4350 - went hunting. At this point in time, I had 150 rounds down the barrel. Never fired a shot during hunt, but I did drop my rifle (not a bad drop at all). I decided to re-zero scope the following week. When I went to the range, I noticed that the same loads were now giving me a sticky bolt and some signs of pressure (cratering & extractor marks).</p><p></p><p>I started to recheck my loads wondering what was going on. All the previous loads with different powders were now showing excessive signs of pressure. I thought it might be the warmer temps, so I kept rounds in fridge/cooler prior to shooting. I double checked the weight of each charge on two different scales. I went back and checked my max COL and then backed off another .02". I reconfirmed case length was within specs. I cleaned the barrel using both BMG 50 and Wipeout to ensure there was no copper build-up. Nothing has helped. </p><p></p><p>This morning I went back to the range. I shot one round of 45.0 gr. of H1000 pulled from my cooler. I experienced serious bolt stick, with cratering and extractor mark on case along with a chrony speed of 3,021 fps (it should have been around 2,900 fps). Rather than shoot the other two, I switched to a cooled round of 38.0 gr. of H4350. This shot resulted in a stuck case where the bolt had to be pounded open with a mallet. The primer had been completely blown out of the pocket with a heavy extractor mark. The chrony showed a reading of 3,063 fps, when it should have been in the 2,750 fps range.</p><p></p><p>I am completely baffled! Where do I go from here? Is it possible that something happened to the bolt/action/barrel when it was dropped? Any ideas?</p></blockquote><p></p>
[QUOTE="azsugarbear, post: 538100, member: 4809"] I have a semi-custom 243 Win. that is built on a Rem Model 7 action. It wears a Brux fluted barrel chambered in PTG's 243 Tactical Match with a 1 in 9 twist. Action is bedded in HS stock. Leupold 4-14x40 scope. At this point, I should probably mention that I have been reloading for 25+ years. During break in of barrel, I loaded and tried several different powders in my Lapua brass. I shot the following ladders with the 105 gr. Berger VLD: H4831sc - 40.0 to 44.0 grains* (settled on 42.5 gr. @ 2,860 ave. fps) H1000 - 43.0 to 46.5 grains* (settled on 45.0 gr.) H4350 - 37.0 to 41.0 grains* (settled on 41.0 gr. @ 2,930 ave. fps) * all loads are within min and max load range recommended by Berger Shot drop chart w/41 gr. of H4350 - went hunting. At this point in time, I had 150 rounds down the barrel. Never fired a shot during hunt, but I did drop my rifle (not a bad drop at all). I decided to re-zero scope the following week. When I went to the range, I noticed that the same loads were now giving me a sticky bolt and some signs of pressure (cratering & extractor marks). I started to recheck my loads wondering what was going on. All the previous loads with different powders were now showing excessive signs of pressure. I thought it might be the warmer temps, so I kept rounds in fridge/cooler prior to shooting. I double checked the weight of each charge on two different scales. I went back and checked my max COL and then backed off another .02". I reconfirmed case length was within specs. I cleaned the barrel using both BMG 50 and Wipeout to ensure there was no copper build-up. Nothing has helped. This morning I went back to the range. I shot one round of 45.0 gr. of H1000 pulled from my cooler. I experienced serious bolt stick, with cratering and extractor mark on case along with a chrony speed of 3,021 fps (it should have been around 2,900 fps). Rather than shoot the other two, I switched to a cooled round of 38.0 gr. of H4350. This shot resulted in a stuck case where the bolt had to be pounded open with a mallet. The primer had been completely blown out of the pocket with a heavy extractor mark. The chrony showed a reading of 3,063 fps, when it should have been in the 2,750 fps range. I am completely baffled! Where do I go from here? Is it possible that something happened to the bolt/action/barrel when it was dropped? Any ideas? [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Reloading
Help! Baffled by High Pressure Signs
Top