Forums
New posts
Search forums
What's new
Articles
Latest reviews
Author list
Classifieds
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Rifles, Reloading, Optics, Equipment
Reloading
bullet runout
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="kraky" data-source="post: 146279" data-attributes="member: 180"><p>Most bullet runnout is caused by pulling the case over the expander ball in your die. When the expander isn't centered in the middle of the die it will pull it off center. Below is what I copy to forums when this topic comes up. I had a friend try this tuning a week ago and he wound up getting less runnout than with his fancy Redding Bushing dies! Here is the info:</p><p></p><p>My $.02 worth---ALL dies with expander balls need tuning. Think about it...a piece of typing paper is .003" thick--what are the odds that the expander is not PERFECTLY centered in a die and could pull a case slightly off center??? Pretty good I'd say. Pull the expander stem out of the die (and now is a good time to clean the inside of the die). Run about 5 brass into the die and see if they come out concentric. If they do (and usually they will) you now have to try and get that stem centered on re-assembly. A great way that helps is to put a piece of very concentric brass up into the die to hold the stem in place as you tighten it down. Sometimes this takes 2 people unless you have 3 or 4 hands. AFter reassembly try sizing some brass and check runnout. If not good then do very small turns of the expander stem--probably 1/32 of a turn at a time. Resize some brass and repeat the small turns. At some point I can almost guarantee that you will get GREAT RUNNOUT CONSISTANTLY. (Somehow, someway the expander spindle will hit almost perfect centering in the die body) I have many dies that consistantly make less than .002" runnout after sizing with most of the brass at .001" and less. I own, hornady, redding, forester, rcbs, and lee dies. ALL OF THEM HAVE BEEN TUNED and most make fantastic ammo and all make good ammo!! I have never ever got a set of dies from any factory that made as good of ammo as those that I have done this simple work with.</p></blockquote><p></p>
[QUOTE="kraky, post: 146279, member: 180"] Most bullet runnout is caused by pulling the case over the expander ball in your die. When the expander isn't centered in the middle of the die it will pull it off center. Below is what I copy to forums when this topic comes up. I had a friend try this tuning a week ago and he wound up getting less runnout than with his fancy Redding Bushing dies! Here is the info: My $.02 worth---ALL dies with expander balls need tuning. Think about it...a piece of typing paper is .003" thick--what are the odds that the expander is not PERFECTLY centered in a die and could pull a case slightly off center??? Pretty good I'd say. Pull the expander stem out of the die (and now is a good time to clean the inside of the die). Run about 5 brass into the die and see if they come out concentric. If they do (and usually they will) you now have to try and get that stem centered on re-assembly. A great way that helps is to put a piece of very concentric brass up into the die to hold the stem in place as you tighten it down. Sometimes this takes 2 people unless you have 3 or 4 hands. AFter reassembly try sizing some brass and check runnout. If not good then do very small turns of the expander stem--probably 1/32 of a turn at a time. Resize some brass and repeat the small turns. At some point I can almost guarantee that you will get GREAT RUNNOUT CONSISTANTLY. (Somehow, someway the expander spindle will hit almost perfect centering in the die body) I have many dies that consistantly make less than .002" runnout after sizing with most of the brass at .001" and less. I own, hornady, redding, forester, rcbs, and lee dies. ALL OF THEM HAVE BEEN TUNED and most make fantastic ammo and all make good ammo!! I have never ever got a set of dies from any factory that made as good of ammo as those that I have done this simple work with. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Rifles, Reloading, Optics, Equipment
Reloading
bullet runout
Top