Recent content by cserwin

I see from reading more on ladder testing that I may have inconclusive results at 200 yd. range from ladder testing. Any thoughts on this, or alternate approaches? If it would be worthwhile at 200 yds. what type of charge increments should I be using?

Thanks for that bit of advice. I think that approach makes sense to me, and would let me get where I need to be with a minimal number of rounds sent down the tube. I'll report back on how this method works out Thanks

Thanks, I think I see that reasonably good accuracy is possible with the Encore. I think I'll do a simple ladder test, after finding the bullet that does the best, and work it out from there best on best velocity range. I learned a rookie lesson yesterday with bullet seating, and shoved the...

I may just do that. Try different bullets, and then do a simple load charge test test to see what velocity range is doing the best, and work it out from there, as well as a seating depth test. I learned a rookie lesson today on bullet seating. I think for now My RCBS dies will do just fine, as...

Thanks for that advice Lefty. I'm a lefty too. Thats why I've not gotten my 300 RUM back yet, but am expecting it by the end of the month. Sounds like I'll be looking at sizable jumps with that gun, and probably some frustrations till I get the hang of it. I think the 7-08 is probably a good...

I'm looking for expert advice as a first timer. I have just loaded, and tested my first test rounds in a 7mm-08 TC Pro Hunter, Bergara barrel. I will be loading for 300 RUM soon, as I am having a build I'm expecting by the end of this month. The break action I know is not a long range action...

Hey guy's, to let you all know where I'm at as a first timer to reloading. I have loaded my first test rounds in 7mm-08. Have not started with the RUM yet, as I have not gotten it back from the builder yet. The 7-08 is a TC Pro Hunter with a bergara barrel. I know not an accurate action type...

Good advice. Safety, and equipment are most important. I'm not looking to milk every last fps known to man. Velocity is secondary to me. I'll trade some velocity for accuracy any day. Like I said for now I'll definitely be airing on the side of caution. Using only components, and loads from manual.

I've got RCBS uniflow measure, trickler, and hand priming tool. I've got RCBS dies, but am noticing everyone seems to be using redding dies. That may come later. For now, I'll see how the RCBS dies work for me. Still wondering why my factory loaded Rem. brass is showing case neck splits after...

Good luck with the antelope, and the 338 build. I'm considering another build, and 25-06 could end up being my choice.

Thats good advice, and I'm guilty of the spending spree. I originally bought a RCBS Rockchucker kit. For now hopefully it will suit my needs. In hindsight I should have done a little more research, and I wish I would have found this site before I got into it. The good thing about modern...

Korhil, I appreciate your advice, and willingness to help. I have pretty much made my investment, some of which I'm sure I will be replacing very soon, as with the case trimmer. Apparently you get what you pay for. And I will be looking for precision accuracy. As I get into it I will be picking...

Thanks for the input. The fascination with long range ballistics has bitten me, and I'll probably go broke searching for that ultimate LR load, and rifle. I must be watching too much TV (Long Range Pursuit), (Extreme Outer Limits), etc. For now its a hobby, but I also do a lot of hunting, and...

Another question is in powder selection. This gun will be used for big game hunting in the Rockies. My load development will be done in 90-95 degree weather. My hunting will be done in much cooler temps, estimated 20-30 degrees. Which of the magnum powders are the most temperature stable? Not...

Thanks for the replies. All the factory ammo by any manufacture I've bought has had a visible crimp, no cannelure. I do agree with Lefty 7mm, and it is probably a manufacturing guideline to crimp bullets of magnum rounds. I'll also be loading .45 acp, and .44 mag, so bullet crimping may be...