Recent content by bradtothebone

Like new, no scratches, dings, dents etc. Complete with original box. Looking for 1000 CDN...... Will work a deal for shipping depending where..... No problem shipping to the states......

Orrrr send 3 fired cases to hornady and get a hydroforming die.... I have one for my .22-250AI and one for my .338LAI and i have had good results..... Plus you dont have to load them up or go to the range/farm or whathave you to fire them off...... brad

well my loads for .338 Lapua Ackely Improved is consisting of 110.5 gr of US869 yielding 2980fps in 20degree celcius temperature, and groups of .557 at 300metres (yrds) this is in an ATR Nesika Custom rifle by LongRanger Bradgun)

I have 2 .204s!! I have a "walking" CZ 527 varminter, and it has produced awesome groups with 39gr BKs which I highly recommend, with a velocity in the 3800+fps range.....Using H4895 I also have a savage BTVS (thumbhole stock) it shoots ALMOST as good as the CZ..... And it loves the 39 BKs...

Not a .338edge but a .338Lapua AI Built on a nesika action with mike rock bbl, Built by Long Ranger on this site, so far at 327 yrds (300m) I have been consistantly getting 1/2 inch groups..... More than happy with that and the 300gr SMKs... Rick does awesome work..gun)

deleteeeeee meeeee meeeeetooooo

A ballistic kin But still shows up 2 spots different on the burn chart...... U do it your way......Ill do it mine. Even though its a BALLISTIC KIN, Id bet that they dont just package some with h414 and then switch to a different labeling/packaging and call it 760...... To each his own...

I used to have a 4200 :cool::cool:then bought my 1st nightforce, a 5.5x22x56 with Npr2 reticle..... I ended up floggin the 4200...... Now I own another nightforce 8x32x56 npr2 reticle....... ANd except for my gopher rig (.204 ruger) I run nightforce or zeiss...... Once you get a taste of...

COW and H414 and 760 COW..... get some 700x shotgun powder, try about 10gr....put in powder, then fill to the top with cream of wheat.......Compact into casing about bottom of neck with a an allen key or whatever..... Use dacron from say a pillow, roll up a little, push in with allen...

you just phone Hornady, talk to Lonnie Hummel, if he is back from his operation.... Im sure if he isnt there somebody can hook you up..... You send in 3 fired cases and 3 unfired cases and they make it custom for you...... I have a set in .22-250AI and have a set of .338 Lapua AI...

velocity is pretty good My first batch was over 4000, I have also used varget to get 4225 but ohhhh the primer pockets were done..... I might try H414 but i am pretty happy with ww760..... :D Coyotes????Welll, lets say it works VERY well..... I shot one in the boiler room at 450yrds, when i...

or use hornadys hydroforming dies I hydro form my brass, prime with spent primer, fill with water, place in press, hit with hammer 3 times, tip water out, deprime, and there you have AI formed brass, no COW no firing....

hornady hydroforming dies are the way to go, although they dont produce the sharp shoulders, sorta rounded, but the capacity is such that you can shoot your normal AI loads without any problems, then they are 100% formed........ You get a special shell holder and die assembly, put a FIRED...

I have a barnard action .22-250AI and have settled on 55gr Noslers, i went with a 1-14 twist, as i wasnt interested in the larger pills, just flat shooting..... I have had with nosler brass, the 55gr up to 4225 fps, which was HOT in my rifle, the results I have found are on the average, 3990...