50 BMG project

mitch260

Well-Known Member
Joined
Sep 5, 2012
Messages
210
Location
Michigan
I've got pretty much all the parts needed to build my 50 bmg:D. I have designed it very similar to a Noreen ULR rifle except I added a hand guard instead of the 7/8" rod. I want to be able to set it on sand bags or some sort other rest, not just a bi-pod.

The barrel I purchased is a 33" mil-spec chambered Mossberg. Does anyone else have a 50 built with one of these barrels? If so how does it shoot? I might end up of taking a half inch or so off the chamber end and renting the match reamer from 4-d. My goal is 1 MOA at a mile, but I'm not 100% sure that's possible. I am confident in my machining abilities (as I've built multiple sub 1/2 minute rifles), but I'm not sure about the barrel. Either way, with all of the steel, aluminum, and the barrel I only have about $300 invested in this project so far.

I am using a Timney Mauser trigger and Limbsaver recoil pad.

Once its done, I have a Millett 6-25X56 to put on it, and I am going to make a 60 MOA base for it, so I'll have about 130 minutes of elevation adjustment. with Amax's I should be able to reach 2500 yards with out much trouble. It will also get a coat of duracoat and possibly hydrodipped.

I figured for about $500 plus my time I couldn't go wrong and I can always upgrade the barrel later on.

Thanks for reading, Any thoughts or suggestions are welcome and appreciated.
Take care
 
I've got pretty much all the parts needed to build my 50 bmg:D. I have designed it very similar to a Noreen ULR rifle except I added a hand guard instead of the 7/8" rod. I want to be able to set it on sand bags or some sort other rest, not just a bi-pod.

The barrel I purchased is a 33" mil-spec chambered Mossberg. Does anyone else have a 50 built with one of these barrels? If so how does it shoot? I might end up of taking a half inch or so off the chamber end and renting the match reamer from 4-d. My goal is 1 MOA at a mile, but I'm not 100% sure that's possible. I am confident in my machining abilities (as I've built multiple sub 1/2 minute rifles), but I'm not sure about the barrel. Either way, with all of the steel, aluminum, and the barrel I only have about $300 invested in this project so far.

I am using a Timney Mauser trigger and Limbsaver recoil pad.

Once its done, I have a Millett 6-25X56 to put on it, and I am going to make a 60 MOA base for it, so I'll have about 130 minutes of elevation adjustment. with Amax's I should be able to reach 2500 yards with out much trouble. It will also get a coat of duracoat and possibly hydrodipped.

I figured for about $500 plus my time I couldn't go wrong and I can always upgrade the barrel later on.

Thanks for reading, Any thoughts or suggestions are welcome and appreciated.
Take care



Sounds like a project worth doing.

How much will it weigh, and what kind of action will you use ?

Lilja makes fine 50 Cal barrels If you do decide to change barrels.

J E CUSTOM
 
Sounds like a project worth doing.

How much will it weigh, and what kind of action will you use ?

Lilja makes fine 50 Cal barrels If you do decide to change barrels.

J E CUSTOM

I am building my own action, very similar to the Noreen. If this barrel doesn't work out very well I am definitely considering Lilja. They seem to have a good reputation in the 50 cal game. As far a weight goes, it will be heavy. I am going to leave this barrel the full 1.65" in diameter, it weighs 18 pounds alone. My guess is that it will be close to 40 pounds or more. If I get a better barrel I will have it contoured to drop some weight.

Thanks for the reply.
 
I am building my own action, very similar to the Noreen. If this barrel doesn't work out very well I am definitely considering Lilja. They seem to have a good reputation in the 50 cal game. As far a weight goes, it will be heavy. I am going to leave this barrel the full 1.65" in diameter, it weighs 18 pounds alone. My guess is that it will be close to 40 pounds or more. If I get a better barrel I will have it contoured to drop some weight.

Thanks for the reply.
Are you going to have to serialize and register the action? Or do you live in one of those states that if you mfg all the parts yourself in your state that it doesn't have to be registered?

I think that's part of the FFA - Firearms Freedom Act.
 
I considered doing a .408, but the Mossberg barrel only cost $180 plus shipping. And I can get surplus FMJ bullets for $0.50 a piece when I don't want to pay $2.50 each for the Amax's. I still want a .408 eventually though, but it would be light weight for hunting.
 
Once you get done let me know what it might cost to buy one. I have been wanting a Noreen ULR .50, but the money hasn't been there. If they are priced right, and shooting good, I might be interested in one, if you decide to make a few.

And yes, definitely post pics!
 
I'd love to build you one, but unfortunately you need to have a manufacturing FFL to make firearms to sell. I am looking at getting one in the not so distant future, but until then I can only build for my self.
 
I'd love to build you one, but unfortunately you need to have a manufacturing FFL to make firearms to sell. I am looking at getting one in the not so distant future, but until then I can only build for my self.

Well, once you do, let me know. :D But in the meantime I can drool over the one you make for yourself. LOL
 
Will do:). Anyone else have any thoughts or suggestions?

Not much in the way of suggestions, but I am curious what material you are going to use for the action. Will it be heat treated after the machine work is finished or will it be roughed in then treated and finished? Or are you basing it off an action you already have? I am definitely going to subscribe and follow this as you go!! :D
 
Warning! This thread is more than 9 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.
Top