Accuracy of a hot barrel?

kherter

Active Member
Joined
Mar 12, 2010
Messages
38
Location
SW Saskatchewan
I was wondering on what your oppinions are on the accuracy of a hot barrel.
Is it best to shoot a few and let the barrel cool or does it not really matter. I have been shooting a few and let cool for a while and some times I get trigger happy and the barrel gets a little hot, Does this really matter? Will this affect my accuracy and will it also shorten the life of may barrel?

gun)
 
If it affects the accuracy is the difference between a real "hummer" and just a good barrel. any good barrel will shoot good if you treat it right (dont let it get too hot, keep it clean, or fouled just enough) a real hummer, will shoot when it's grimy and hot.

A hot barrel, presumably also fouled (unless you didnt heat it by shooting, a lot) will increase the pressure and increase the velocity of your round, but probably not predictably, this usualy brings people out of the "node" they worked to get into during load development.

Yes it will also shorten barrel life, can't exactly think of how to explain, except that the steel becomes weaker as it heats up and the bullets do more "damage" scraping over the super hot steel than cool steel.
 
If you really want to know what the barrel will do, wait 3-5min between shots and don't shoot 3, then wait. If you spread the time out evenly each round will encounter roughly the same chamber conditions. If you shoot a string and then wait, the chamber will be cooler for the first round and heat up for the later rounds in the string, increasing your spread.
 
Most top end barrels that are properly stress relieved will shoot very well with a hot barrel. iF they do not, its is generally because of many possible problems:

1. Stress in the barrel steel
2. Barrel contact with stock as it heats up and expands making shots walk.
3. Bullet/load/barrel combo is on the ragged edge for the bullet used and the added barrel heat is causing the bullet to suffer in flight, generally because of jacket core seperation.

The main issue with a barrel getting hot is really not a concern of accuracy if the rifle is assembled properly and a good barrel is used with an appropriate bullet. The real problem with shooting in a hot barrel is throat life.

Keep this in mind, shots 1-3 will do X amount of erosion to a throat, shot 4 will generally do as much as the first three shots. Shot 5 will double that, shot 6 will double that.

Now I am talking about VERY small amounts of throat erosion but once the barrel heats up, throat erosion accelerates dramatically with follow up shots. Now this is certainly dependant to some degree on the intensity of the chambering. A 308 Win will have much less effect on bore temps then say a 7mm RUM.

So to be honest, I would not recommend shooting in a hot barrel if at all possible to avoid weither the barrel shoots well or not, either way, it accelerates the damage to the throat when doing so.
 
This is a very good question. First factory tubes as well as actions, bedding are not really conducive to adding heat because of the stress that is present. Stress in the steel in a perfect world is completely relieved during heat treating. Unfortunately mass produced rifles are not processed for the optimum performance rather a balance of affordability and performance.

A good barrel for example Krieger placed on a rifle that has been properly built on a prepared action and proper bedding job will not change POI when heated. I have sporters as well as match rifles that show absolutely no affect when barrel temps (heat also migrates to the action and stock) are elevated to the point of you cannot handle the barrel.

In my experience while watching others make this mistake is that when the temp of the chamber does rise considerably many people will chamber a round and leave it for a period of time while they adjust the rifle in the rest to shoot. This is not a good thing because as the round heats the powder being at an elevated temperature compared to the previous rounds will have a higher pressure therefore a different pressure curve causing the bullet to have a different POI and this will be especially apparent at longer ranges evidenced by vertical dispersion.

The argument about hot barrels and throat erosion is an old debate that some believe in others do not. The testing results on a 6ppc that were conducted by a friend of mine and a well known shooter and Smith shows it to be of little concern with that specific cartridge. This testing was done on non factory barrels FWIW.
 
If it's a factory barrel then I would shoot one and wait 5 or even 10 Min. then shoot another . usually I would shoot 3 shot groups this way . When factory barrels get hot the accuracey falls off . The shoot and wait gives the rifle a "fair" chance. I shoot a broughton on my .300 RUM and the barrel maker said to shoot 2 fowlers and get on target and send 3 down the tube as fast as possible . It made nice little groups . Could I have done this with my factory barrel in this chamber NO.. I got so tired of waiting for the barrel to cool . Now I don't have that problem .:)

Just my .02

BigBuck
 
Lots of good info. But...

Can someone define hot?

I'll take a stab at it :) I used to say it was hot .If it felt that way when I touched the outside of the barrel so once I didn't "feel" anything or very little I would go ahead and shoot. But I noticed that when I fired that next shot the barrel would heat right back up like I had just shot another 3 round group. remember the barrel heats up from the inside out so what seems to be cool isn't always cool:cool: This is the reason you have to pull out the Old timer pocket knife and whittle 10, 20,30 minutes until you think it's cool. Thank goodness for custom barrels:)

This thread is bringing back some old memories.

One of the things I used to do was take out the bolt and prop my rifle up in the corner with the muzzle up that way the heat would rise out of it like a amoke stack :D I really don't know if this helped or if it was just a habbit.

Bigbuck
 
I used to use a wait a specific time for my barrel to cool, usually I would watch my clock for 3 minutes between shots. The problem is that ambient air temp and the sun have a lot to do with how fast the gun cools down. So I felt like I may have been getting inconsistent temps between shots. So I went to Northern tool an bought one of those small laser thermometers. The kind where you point it at an object, hit a button and it tells you what the temp is. Now mind you I just bought the little pen sized one for $25, but it does a pretty good job.
So now when I shoot I pick a specific spot on my barrel, say the stamed "W" in Winchester for instance and use that as my reading point. I will take a shot and then sit and get the temp off that spot until it goes below a specific temperature before the next shot. I wont take the next shot until it goes below 85 degrees F. So as soon it drops below that point I take the next shot. So my barrel is at the same temp +/- 3degrees every time I shoot.
Maybe I am being to anal but the thermometer didnt cost much and I know I have consistency in barrel temps now, isn't that the name of this game?:)
 
In Louisiana in July and August.....leave ya rifle out in the sun for just 5 minutes and your barrel will do anything you wish to an egg....and you could probably grill a thick steak on it!!:cool:
 
In Louisiana in July and August.....leave ya rifle out in the sun for just 5 minutes and your barrel will do anything you wish to an egg....and you could probably grill a thick steak on it!!:cool:



Well you are an IDIOT to do that unless you have a fluted barrel!!!!

Go ahead and ask me why? :)
 
Warning! This thread is more than 14 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top