Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Gunsmithing


Reply

Update on braked rifle bullets keyholing Part II

 
LinkBack Thread Tools Display Modes
  #1  
Old 03-29-2010, 12:19 PM
Platinum Member
 
Join Date: Jul 2004
Location: SW MO
Posts: 1,110
Update on braked rifle bullets keyholing Part II

Here is a quote of my previous update, would rather not bring the whole thread back up.

"Update on braked rifle, bullets keyholing

--------------------------------------------------------------------------------

For those of you who read my previous thread about bullets keyholing from a newly acquired rifle, here is an update as I'd rather not bring the old thread back up to the first page.
The rifle was supposedly a 300 Ultramag and turned out to be a 338 barrel blank that was chambered with a 300 Ultramag reamer. After much stress and grief, I finally got in touch with the gunsmith who originally did the work (actually done by a person no longer employed by that gunsmith). He has ordered a 30 cal select match SS blank from Shilen as was originally intended for the rifle. He is going to rebarrel the rifle correctly and gave me assurances that he is personally going to do all the work. At this point, we are just waiting on the blank from Shilen. I'm certainly happy that there is a resolution in sight but I'll still be holding my breath until I actually get the rifle back in my posession and put a couple of hopefully tiny groups down range.
I'll update after I receive the rifle, should be 7 or 8 weeks on the blank according to Shilen.
Thanks for all the input on the previous thread.

Sam"


Well, I finally got the rifle back from the gunsmith last week along with 3 fired cases and the receipt for the shilen select match 30 cal barrel blank. He chambered in in 300 Ultra Mag and installed the oversized lug that was supposed to have been on there. He installed and timed the brake properly.

I went to the range yesterday and fired 5 rounds cleaning in between each. Bore sighted and fired the first round and was pleased to see a round bullet hole in stead of a profile hole like before! Adjusted windage and elevation and fired the next 4 rounds. Shots 3, 4 and 5 went into a half inch cluster with shot 2 being below them for about 0.85" total at 100 yards. Not bad for the first load tried during the break in process. I believe this rifle will shoot. I was using 200 gr Accubonds as this is what I am going to launch at elk. The barrel is 28" and I am hoping for 3200 fps but will go by what the brass and chrony tell me.

This whole ordeal has taken the better part of 5 months and I'm glad that it appears to finally be over. The gunsmith was very helpful and appologetic and I appreciate his honesty. I am not going to mention his name but I will say that it is not one of the smiths who frequent or sponsor this site.
__________________
Lefties are the only ones in their right minds!
(and I ain't talkin' politics!)

NRA Life Member
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Update on braked rifle bullets keyholing Part II
Thread Thread Starter Forum Replies Last Post
Wildcat Bullets Update WildcatB Rifles, Bullets, Barrels and Ballistics 80 12-23-2013 01:45 PM
Update on braked rifle, bullets keyholing sambo3006 Gunsmithing 12 02-05-2010 11:28 AM
Berger Bullets 2010 Update ADMIN Miscellaneous LRH Video 8 01-29-2010 08:02 PM
Bought braked rifle, bullets keyholing! sambo3006 Gunsmithing 21 01-14-2010 08:25 PM
keyholing bullets 1doug Rifles, Bullets, Barrels and Ballistics 18 10-04-2005 06:25 AM

Current Poll
Have You Ever Backpack Hunted?
YES - 62.21%
976 Votes
NO - 37.79%
593 Votes
Total Votes: 1,569
You may not vote on this poll.

All times are GMT -5. The time now is 10:15 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC