Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Gunsmithing


Reply

Picatinny style base and ring installation

 
LinkBack Thread Tools Display Modes
  #1  
Old 02-09-2011, 06:12 PM
Platinum Member
 
Join Date: Jul 2004
Location: Texas
Posts: 5,384
Picatinny style base and ring installation

The proper way to install this system seems simple, but there are things that can be done
that will assure better performance of the system.

1=first install the base using 222 Loctite low strength or the blue Loctite. If you want to you can add
a small dab of bedding compound under each end of the base at this time.(Wipe off any excess
before it hardens).

2=Torque the base screws @ 20 inch pounds.

3=Place the rings at the location and spacing that best fits your scope and snug them down (Not
tight).

4=Paint or match mark the rings so they go back the same way (Some are bored and then cut
and they fit better), remove the top half of the rings and lay the scope in the lower half.

5=Move the scope forward or backward to get the optimum eye relief and then level it up.

6=Place the top half of the ring(In the proper lower half and make the screws up snug.

7=Loosen the ring to base screws just enough to let the ring align to the scope and now you
can tighten the scope ring screws Handy.

8=Push the scope and rings forward to remove any slack between the bases and the Picatinny
base slots.

9= Now you can tighten the ring to base screws at the manufactures recommended torque.

10= With these screws tight you can go back and loosen the ring screws to make any final
adjustments without damaging the scope. (Should prevent ring marks)

11=You can now take the scope off, and as long as you push the scope and rings forward each
time you place it back on the base, recoil should not move it, changing your POI.

It may sound complicated but it isn't and it makes everything very repeatable. And after a while
it becomes second nature.

There is a torque spec for all of the screws on a rifle. If you do a search for "Torque Recommendations"

This is just the way I do it and I'm sure it is not the only way, but it works for me and might for others.

Maybe this will help those that are new to picatinny installations.

J E CUSTOM
__________________
"PRESS ON"
Reply With Quote
  #2  
Old 02-09-2011, 10:08 PM
Platinum Member
 
Join Date: Apr 2010
Location: Allen, TX
Posts: 2,608
Re: Picatinny style base and ring installation

I have some beautiful Beuhler split rings on my K14. What a pain in the rear to work with!

I wish I had discovered picatinny 30 years ago. Clean and simple.

Thanks for the post.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Picatinny style base and ring installation
Thread Thread Starter Forum Replies Last Post
Picatinny vs DNZ style integrated base. emmagator Long Range Scopes and Other Optics 9 01-03-2011 10:00 PM
Swarovski 1" picatinny style rings CBS Optics For Sale 0 12-21-2010 03:09 PM
Wanted 20 MOA Picatinny style base Rem 700 POP Optics For Sale 3 02-01-2010 08:26 AM
Dimensional differences between Weaver-style and Picatinny bases??? str8flite Long Range Scopes and Other Optics 1 07-02-2009 10:03 AM
Burris 30mm Xtreme Tactical Picatinny -Style Rings ricka0 Long Range Scopes and Other Optics 0 01-03-2005 03:07 PM

Current Poll
Are you on Facebook?
Yes - 46.51%
1,093 Vote
No - 19.32%
454 Votes
No, but I may join - 1.74%
41 Votes
No way, are you kidding? - 36.21%
851 Votes
Total Votes: 2,350
You may not vote on this poll.

All times are GMT -5. The time now is 05:55 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC