Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rimfire and Airguns


Reply

Homemade rim thickness gauge

 
LinkBack Thread Tools Display Modes
  #1  
Old 03-30-2010, 09:10 PM
Silver Member
 
Join Date: Nov 2008
Location: NORTHEAST PA.
Posts: 225
Homemade rim thickness gauge

The reasoning behind sorting rimfire ammunition by rim thickness sounded very valid to me. The concept is that headspacing varies when the thickness varies, and since rimfire ammo headspaces on the rim of the cartridge, if you can take out the variances by measuring and lotting "like" thicknesses, you will improve accuraccy. Just as in reloading, differing overall lengths and seating depths produce differing results, hampering steady consistancy.
Enter the rim thickness gauge.
As always looking for a way to economically improve performance, I finally decided to purchase a rim thickness gauge. I did a search on the net to find manufactures when I cam across a froum thread on making your own rim thickness gauge. After reading it, I immediately went to my reload bench to get started, and after just a few minutes, put together my own thickness gauge.
Items needed: calipers, and one spent or new .243 case. In the original thread, the gentleman used a .223 case, which seemed a natural choice, but I found that it scrapped off the valuable lubrications on rimfire ammo. So I went with .243. I also had some 3M non skid stick on material around so I thought I'd use it also.

I took the casing and put it on the trimmer to give it a nice flat and even lip. Ironically I used the same calipers used for the rim thickness gauge to so several measurements while turning the casing to ensure it is as flat and even as I can get it. I then took a neck brush to clean the inside of the neck of any residue. I shined the brass up a bit with never dull (for looks) and wrapped the non skid around the casing for grip and to designate it as a casing I want to keep for a special purpose.
I then simply put the casing in the calipers, closed the jaws and zeroed out the calipers.

To measure rim thickness on rimfire ammo, just slip the rimfire round into the opening of the case. The mouth of the .243 case bumps up against the rim and is not too wide as to allow the rimfire case from falling in the .243 case.

Now just put the calipers back on the .243 case with the rimfire case in it and take a measurement. The reading is the rim thickness.
My first 3 measurements....



Now to weigh a few more and see if the concept is real, which means another one of my long winded ammo tests. Will be updating with results soon.
__________________
...that's what i like about toe tags; one size fits all...
Reply With Quote
  #2  
Old 03-31-2010, 09:30 AM
Silver Member
 
Join Date: Feb 2002
Location: Rapid City, South dakota
Posts: 410
Re: Homemade rim thickness gauge

Nice. Been thinking about buying a commercial model myself but I'm now thinking Hmmm.
Reply With Quote
  #3  
Old 08-23-2010, 01:39 PM
Bronze Member
 
Join Date: Aug 2010
Location: North Wales UK
Posts: 41
Re: Homemade rim thickness gauge

what a clever idea , nice work buddy - a little garage project coming up me thinks Gary
__________________
Theoben R7 Rapid "S", .22 , P.Wilson thumbhole AWT, CZ 452 .17 HMR / Ruger 10-22 / Dedicated Ruger 10-22 NV / .223 Remy PSS / .243 Remy Varmint / .204 Remy Varmint Betinsoli diamond 12g
Reply With Quote
  #4  
Old 01-13-2011, 09:33 PM
Junior Member
 
Join Date: Oct 2010
Posts: 6
Re: Homemade rim thickness gauge

great tip!
Reply With Quote
  #5  
Old 02-13-2012, 01:28 PM
Silver Member
 
Join Date: Nov 2008
Location: IDAHO
Posts: 150
Re: Homemade rim thickness gauge

Thank you for the great tip.

I think it would be nice to see a correlation of targets in reference to different rim thicknesses.

Also do you have any suggestions on how to even up the bolt headspace? My 10/22 bolt is not exactly even when I measure both sides of the bolt. I feel this aligns the bullet with a tilt at the very beginning.

Opinions????

ODAVID
Reply With Quote
  #6  
Old 02-13-2012, 06:35 PM
Silver Member
 
Join Date: Nov 2008
Location: NORTHEAST PA.
Posts: 225
Re: Homemade rim thickness gauge

i did have targets, however through the passage of time and alot of targets lying around i cleaned house just this weekend and no longer have them.

however i do believe i have a post around here somewhere titled "weighing ammo vs. rim thickness" or something like that.

i do believe there are pictures there at 50 and 100 yards.

to cut to the chase of it there were 3 or 4 different ammos both sorted by weight and by rim thickness. it appeared that at 50 yards, the rim thickness was the winner, but at 100 yards it seemed that weight sorting the ammo took more of a precedence. this also seemed apparant at 150 and 200 yards.

my conclusion was whatever it is about weight sorting is of greater value at longer distances. but for around the 50 yard mark, rim thickness was the clear winner.
__________________
...that's what i like about toe tags; one size fits all...
Reply With Quote
  #7  
Old 03-04-2014, 04:02 PM
Junior Member
 
Join Date: Mar 2014
Posts: 1
Re: Homemade rim thickness gauge

Quote:
Originally Posted by top predator View Post
i did have targets, however through the passage of time and alot of targets lying around i cleaned house just this weekend and no longer have them.

however i do believe i have a post around here somewhere titled "weighing ammo vs. rim thickness" or something like that.

i do believe there are pictures there at 50 and 100 yards.

to cut to the chase of it there were 3 or 4 different ammos both sorted by weight and by rim thickness. it appeared that at 50 yards, the rim thickness was the winner, but at 100 yards it seemed that weight sorting the ammo took more of a precedence. this also seemed apparent at 150 and 200 yards.

my conclusion was whatever it is about weight sorting is of greater value at longer distances. but for around the 50 yard mark, rim thickness was the clear winner.
From what I have read, both seem to hold true to what you are saying, however the way it seemed they got absolutely the best on long range was to gauge rim first, then weigh for powder differences. Seems logical but have not had a chance to go out and shoot to be able to report results. Will let you know after.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Homemade rim thickness gauge
Thread Thread Starter Forum Replies Last Post
homemade anemometer crowsnest2002 Equipment Discussions 0 05-15-2011 11:37 AM
Homemade Zerostops LRSickle Long Range Scopes and Other Optics 50 04-25-2011 12:53 PM
homemade zerostop dud Long Range Scopes and Other Optics 3 04-16-2010 11:17 PM
Rim thickness gauge? bowhunthard Rimfire and Airguns 4 02-26-2009 05:41 PM
OAL gage (homemade) Bob S. General Discussion 4 09-02-2005 08:13 PM

Current Poll
Do you archery hunt for elk?
YES - 31.72%
59 Votes
NO - 52.69%
98 Votes
Not yet, but I plan to. - 15.59%
29 Votes
Total Votes: 186
You may not vote on this poll.

All times are GMT -5. The time now is 07:11 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC