Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

Remminton Brass is $!@$

 
LinkBack Thread Tools Display Modes
  #1  
Old 03-05-2009, 02:30 PM
Silver Member
 
Join Date: Dec 2008
Location: Somewhere in Kansas
Posts: 247
Remminton Brass is $!@$

I recently bought 100 rounds of remmington brass went to use them today and over 60% of them had dents in the neck then once i had resized them to fix the necks and primed them i was deburring and chamfuring 50 of the of witch 3 had split necks WTH
Reply With Quote
  #2  
Old 03-05-2009, 02:39 PM
Platinum Member
 
Join Date: Jan 2008
Location: SOCIALIST CONTROLLED TERRITORY OF NEW YORK
Posts: 4,388
Re: Remminton Brass is $!@$

If thats new brass you got screwed!

I always resize new brass however.
Reply With Quote
  #3  
Old 03-05-2009, 02:41 PM
Platinum Member
 
Join Date: Feb 2007
Location: Townsend, Montana.
Posts: 7,761
Re: Remminton Brass is $!@$

Holly Crap! What caliber? What dies? Were you expanding them up?

Jeff
__________________
Reply With Quote
  #4  
Old 03-05-2009, 02:48 PM
Bronze Member
 
Join Date: Dec 2007
Location: Surprise, AZ
Posts: 53
Re: Remminton Brass is $!@$

Looks like someone got them stuck and pulled them out with pliers
Reply With Quote
  #5  
Old 03-05-2009, 02:50 PM
Silver Member
 
Join Date: Dec 2008
Location: Somewhere in Kansas
Posts: 247
Re: Remminton Brass is $!@$

.204 with a redding neck sizeing die i haven't gone through the other 50 yet and i mashed the case with pliers so i wouldn't use them.
Reply With Quote
  #6  
Old 03-05-2009, 03:00 PM
Junior Member
 
Join Date: Feb 2009
Posts: 15
Re: Remminton Brass is $!@$

I ordered 1000 remington cases from Cabela's. I have neck sized and deburred the flashholes on about 600 so far, and not found a bad case. These are also for the 204
Reply With Quote
  #7  
Old 03-05-2009, 03:08 PM
Platinum Member
 
Join Date: Dec 2002
Location: Northern Michigan
Posts: 1,014
Re: Remminton Brass is $!@$

The dents are common and from my experience they don't hurt anything. It has to do with the way they tumble their cases in large quantities. Usually they come with a little orange piece of paper warning about this, though that may be a Midway thing.

Split necks also happen. I've ordered may hundreds of RUM cases and usually get a few split necks. I've also had Lapua brass in .243 with split necks (2 of 100). Toss them in the junk bin and move on.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Remminton Brass is $!@$
Thread Thread Starter Forum Replies Last Post
338 Lapua Brass compared to 300 Remington Ultra Brass DANTEC Rifles, Bullets, Barrels and Ballistics 6 02-29-2012 11:43 PM
Group differences in Weatherby Brass versus new Norma Brass TX mountain hunter Long Range Hunting & Shooting 5 12-29-2010 10:17 PM
25-06 reloading dies, brass, and bullets / 45ACP brass jeffro Reloading Equipment and Components 1 05-01-2010 10:51 AM
338 Edge, Brass life test. Rem 300RUM brass AJ Peacock Reloading 15 12-30-2009 12:26 PM
Nosler Brass cosmetic seconds good brass? sambo3006 Reloading 6 01-04-2007 08:57 PM

Current Poll
Are you on Facebook?
Yes - 46.40%
1,114 Vote
No - 19.53%
469 Votes
No, but I may join - 1.75%
42 Votes
No way, are you kidding? - 36.07%
866 Votes
Total Votes: 2,401
You may not vote on this poll.

All times are GMT -5. The time now is 10:36 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC