Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

Need 7mm RUM load info

 
LinkBack Thread Tools Display Modes
  #1  
Old 11-02-2005, 05:19 PM
Platinum Member
 
Join Date: Jul 2002
Posts: 2,856
Need 7mm RUM load info

I'm looking to get some loads worked up for a 7mmRUM and was wondering what everybody is using for it? I'm planning to shoot the Nosler 160gr Accu-Bond

Any load data is apperciated
__________________
Si Vis Pacem Parabellum
Molon Labe
Reply With Quote
  #2  
Old 11-02-2005, 08:39 PM
Gold Member
 
Join Date: Jan 2005
Location: N.C
Posts: 540
Re: Need 7mm RUM load info

Try working up to 90.5 grains of H-1000 over CCI 250's with the 160 Accubond seated to fit the mag. If that doesn't work try Retumbo up to 96 grains with the same primer or my personal fav Rem 9 1/2 Mags. Let me know if you have some other bullets in mind and I just might have some data for em.
__________________
Guns and ammo, what more do we need?
Reply With Quote
  #3  
Old 11-02-2005, 09:47 PM
Silver Member
 
Join Date: Nov 2003
Location: Missouri
Posts: 167
Re: Need 7mm RUM load info

not exactly what you are looking for, but I have been shooting 162 Amax's pushed by 85 gr RL22 with Win Mag large rifle primers. Don't know the velocity, but very accurate.
Reply With Quote
  #4  
Old 11-03-2005, 08:53 AM
Bronze Member
 
Join Date: Jan 2004
Location: Cedar Hills, Ut
Posts: 95
Re: Need 7mm RUM load info

Ive had good luck with 160gr Accubond, 89gr. R25,Fed 215m seated at 3.59 out of a custom M70, 27" pac-nor barrel. under .5moa. 3350fps.
__________________
Thanks, LiteTac
Reply With Quote
  #5  
Old 11-04-2005, 01:26 PM
Junior Member
 
Join Date: Feb 2005
Posts: 18
Re: Need 7mm RUM load info

RL-25 shoots faster in my Savage 116 then Hornady Manual figures, 84 grains with Fed 215 and Hornady 154 SST shows 3100 on chrono. AA8700 shoots same bullet slower then books loadings. However, without neck size only, my primers look very flattened with any load?? Bullets not touching lands. Headspace has been checked with gauges.
This round seems very "finicky" in this rifle. With FL resizing, cases were starting to show head separation after 3 firings. Check with RCBS case mic showed fired cases were stretching .005, (within SAMMI), from factory loaded cases and same with reloads from FL RCBS die. Just started neck size only to see how cases last.

Took Antelope at 260 yds with 154 SST. Thorax hit with 4 inch exit hole. Lope still ran 60 yds. with lungs and heart jellied.
Reply With Quote
  #6  
Old 11-04-2005, 11:11 PM
Silver Member
 
Join Date: Jun 2005
Posts: 155
Re: Need 7mm RUM load info

I want to try the 160 accubond as well. Right now I am shooting a 150 gr partition, Rem case, Fed 215 primer, 95 gr. RL25, OAL 3.670 if you try this load, work up from well below as each rifle is different as is each different lot of powder. For me, this load Chrono's ave 3450 @15ft. 3 shot group at .75 inch @ 100 yd. I shoot it through a factory 700 LSS. For me, this load goes into the magazine, feeds well, doesn't exhibit pressure signs, and kills animals. I want to try the 160 accubond to see if it shoots flatter than the 150 partition out to about 450 yds. Until I shoot more/practice more. I have no business shooting further.
Reply With Quote
  #7  
Old 11-06-2005, 10:37 AM
Gold Member
 
Join Date: Dec 2002
Location: mathias wv
Posts: 985
Re: Need 7mm RUM load info

180 pilot, I think your resizing to much, you set the die to your chamber? also if your shooting a fed 215 primer, they have a soft cup and flatten some with any normal load, this is according to a tech at sierra bullets.
JS
__________________
Born to Hunt, Forced to Work!
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Need 7mm RUM load info
Thread Thread Starter Forum Replies Last Post
.300 WSM Load info HDTony Reloading 9 08-26-2010 07:47 PM
Need load info for 6.5/06 nctta Reloading 1 07-25-2010 12:44 AM
6.5- 284 load info 1eye Reloading 2 02-17-2009 06:42 PM
.223 Rem. load info. cjp45 Reloading 7 02-26-2006 11:26 PM
.260 Gas Gun load info KS Rifles, Bullets, Barrels and Ballistics 2 08-19-2003 07:47 AM

Current Poll
Spot & Stalk or Ambush For Western Deer?
MOSTLY - Spot & Stalk - 73.73%
1,027 Vote
MOSTLY - Ambush - 26.27%
366 Votes
Total Votes: 1,393
You may not vote on this poll.

All times are GMT -5. The time now is 05:25 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC