Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

Neck tension-- how much ???

 
LinkBack Thread Tools Display Modes
  #1  
Old 03-17-2010, 10:40 PM
GNERGY
 
Posts: n/a
Neck tension-- how much ???

I was resizing some 338 Ultra mag cases today. I have both Hornady and Lyman dies and was checking the sized ID of the neck.
Hornady .330 ID
Lyman .333 ID
So I was thinking the .333 ID would be less sizing and expansion of the brass and still have a good grip on the bullet to keep it from moving in the magazine.
How much neck tension do you really need, or what is best?
I have 2 rifles that are single shots so how much tension do you need for use or them?

Thanks, Tarey
Reply With Quote
  #2  
Old 03-17-2010, 10:49 PM
Platinum Member
 
Join Date: Aug 2003
Location: NC, oceanfront
Posts: 3,296
Re: Neck tension-- how much ???

On the single shots 1thou is enough.
Otherwise I suggest you use no more than needed.

10% variance in low tension is alot less than 10% variance in high tension..
Reply With Quote
  #3  
Old 03-18-2010, 09:12 AM
Platinum Member
 
Join Date: Oct 2007
Location: Mountians of SW NC, near Asheville
Posts: 1,596
Re: Neck tension-- how much ???

Good question, easy answer. Not simple to explain because it runs counter to what is commonly understood about bullet tension. I'll try.

Basically, Mikecr is absolutly correct, "best" "tension" is 1 to 1.5 thou. In fact, it isn't physically possible to even have more than about 1.5thou.

What most people call "tension" isn't. What they mean is how much smaller the neck ID is than the bullet, that's what machinests call an "interference fit", a jam-fit actually. Tension is NOT properly the amount of force needed to jam the bullet in, it's really the amount of pull required to take it back out.

Our cases have enough elasticity, or spring, in them to allow them to retain a springyness that holds the bullets in place. But, if it's stretched too far the elastic of limit of the brass is exceeded and it just permantly stretches/expands. (That's what happens when we fire the rounds, the neck is "permanently" stretched too large to hold another bullet until we "permanently" squeeze it back smaller.)

The elastic limit of common case neck brass is about 1 - 1.5 thou, rarely as much as 2 thou (it does vary a little by the physical size of the neck). If your .338 neck was sized and ball expanded to .330 your bullets will have to stretch it to .338 during seating. That much difference requires a noticible force to push them in and some feel that means it will hold the bullets tighter; it doesn't. You can prove that by seating, measuring the neck diameter, pulling the bullet and measureing it again; it will likely spring back only 1-2 thou from loaded diameter. Proving that no matter the neck diameter before seating, the permanent difference will only be 1 or 2 thousants (depending somewhat on how and where the measurements are taken and the original diameter of course). Thus, we can permanatly expand with an expander OR with a bullet but the end tension will be the same in either instance. There is no bullet tension value to expanding a neck to less than about 2 thou under bullet diameter.

One significant factor in having lower seating tension (in your case that would ideally mean an expander of .336"- .337") is that less force needed to push the bullets in so they will enter more easily and, from that, tend to go in straighter.

One rarely understood value of the Lee collet neck sizer die is it frequently achieves a proper REAL bullet tension fit.

Last edited by boomtube; 03-18-2010 at 03:52 PM.
Reply With Quote
  #4  
Old 03-18-2010, 08:34 PM
Gold Member
 
Join Date: Jun 2006
Location: Shangri-La
Posts: 930
Re: Neck tension-- how much ???

I agree with boomtube, I have done the test and measured with pin gauges accurate to within .001". I sized necks from a 264 caliber case with 3 different size mandrels

mandrel size / # fired case / sized case pin size / pulled bullet pin size
.262" mandrel / 5 times fired / .263" / .263"
.262" mandrel / 1 time fired / .262" / .263"
------------------------------------------------
.261" mandrel / 5 times fired / .261" / .263"
.261" mandrel / 1 time fired / .261" / .263"
------------------------------------------------
.260" mandrel / 5 times fired / .260" / .263"
.260" mandrel / 1 times fired / .260" / .263"

notice the pulled bullet pin size was the same. So I size all ID's to .003" below caliber to make sure I get consistant stretching of the brass and go from there. Other than crimping, I don't think you could get any more bullet grip even if you sized the ID down to .010" below caliber.

Now there is another factor in bullet grip other than ID and that would be the surface interface of the bullet and the inside of the neck. Imagine the inside of the neck having multiple scratches and burrs as opposed to a completely smooth inside neck surface that was coated with a dry lubricant like graphite or mica. IMO there would be a difference in the amount of force needed to pull the bullet.
__________________
If you can read this, thank a teacher.......if you are reading this in English, thank a soldier.
Reply With Quote
  #5  
Old 03-19-2010, 06:48 AM
Platinum Member
 
Join Date: Aug 2003
Location: NC, oceanfront
Posts: 3,296
Re: Neck tension-- how much ???

Woods, yes frictional differences affect pull force. But this is not a factor.
A neck fully expands on firing before the bullet has moved.

What does affect tension in a meaningful(and useful) way, is the amount of neck sizing length. This can be useful for tuning with some component combinations.
I start off with one cal of neck sizing at 1thou under(after springback).
Just an easy standard for me, that's worked well w/regard to ES.

Some day I'll play with it further(best load over wide temp range-vs-tension).
But my main focus has been tension variance, as compared with an instrumented mandrel.
Reply With Quote
  #6  
Old 03-30-2010, 06:12 AM
Silver Member
 
Join Date: Jan 2006
Location: South Africa
Posts: 420
Re: Neck tension-- how much ???

Sorry to ressurect this, but I've been away and as I was hunting I figured you may forgive me...

MikeCR, a question for you please and anyone else who wants to chip in...

Okay, so I hear you, the neck expands before the bullet moves. The pull force would in my opinion (theoretically?) determine the "dwell time" or contribute to it. So if the internal neck surface creates more friction, then the dwell time may be a little longer. Also, the internal neck surfaces should ideally be pretty similar to ensure consistency in performance. Your thoughts?

As an aside, I don't suggest that a smooth surface has less friction than a slightly rougher once cleaned with a brass brush for example as opposed to one that's polished, as the surface area actually contacting the bullet jacket may be less with a rougher surface, but this isn't relevant for my purposes, so I haven't really thought about this much.

Thanks for sharing your thoughts.

WL
Reply With Quote
  #7  
Old 03-30-2010, 08:35 AM
Gold Member
 
Join Date: Jul 2007
Posts: 940
Re: Neck tension-- how much ???

This is like overthinking the sun rising in the east, it really dosn't matter as long as it's CONSISTANT.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Neck tension-- how much ???
Thread Thread Starter Forum Replies Last Post
Neck Tension 7mm Eclipse Reloading 6 09-06-2010 06:22 PM
How much neck tension BillR Reloading 8 09-23-2007 12:17 AM
neck tension col48 Reloading 0 08-06-2006 02:28 AM
neck tension col48 Reloading 8 05-02-2006 12:51 PM
Neck Tension? tdv75098 Reloading 6 02-13-2005 07:04 PM


All times are GMT -5. The time now is 06:40 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC