Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

Help! Case neck runout...bent decapping rod?

 
LinkBack Thread Tools Display Modes
  #1  
Old 09-27-2011, 12:55 AM
Bronze Member
 
Join Date: Jul 2011
Location: manitoba, canada
Posts: 80
Help! Case neck runout...bent decapping rod?

Looking for some recommendations from some more experienced reloaders here...

I was prepping some new Lapua 308 brass today and I was running them all through my rcbs fl competition die to fix the necks cause some of them were dented and out of round..
I noticed the case neck run out was going from 0 to 1 thou presizing to 10 to 15 thou post-sizing! So after banging my head against the reloading bench screaming WTF! I pulled the die apart and took a look at things but couldn't see any obvious problems... So I tried sizing a couple pieces without the decapping rod/expander button and low and behold the runout was back down to 0-1 thou.. Put the expander back in and it was right back to 10-15 thou... Didn't matter if I ran the expander right up close to the neck of the die or right down near the case head, or had the rod free floating or clamped tight with the locknut... Lube in the inner surface of the neck didnt help...
So now I'm pretty sure the decapping rod is bent....
What should I do? Order a new decapping rod and wait god knows how long to get one in the mail? Just bite the bullet and spend $100 bucks or so and get a bushing die set from redding and again wait for delivery?
Or, since I am loading with vld boat tails can I just let the bullet do the neck expansion for me?

Is this gonna run me into neck tension problems if I do this?

Thanks in advance for any insight...


Orch
Reply With Quote
  #2  
Old 09-27-2011, 05:06 AM
Platinum Member
 
Join Date: Jan 2007
Location: PA
Posts: 1,046
Re: Help! Case neck runout...bent decapping rod?

Remove the expander from the decap rod. Lay the rod on a flat surface and roll it slowly. You should be able to see a small wobble if it is bent. A bent decap rod will definitely cause run out. Call RCBS and they will send you a new decap rod for free.

The expander is your worse enemy, and puts much stress on necks, in addition to frequently causing run out. Get a bushing die.
Reply With Quote
  #3  
Old 09-27-2011, 08:25 AM
Platinum Member
 
Join Date: Oct 2007
Location: Mountians of SW NC, near Asheville
Posts: 1,589
Re: Help! Case neck runout...bent decapping rod?

Get a Lee Collet Neck Die and get good necks without fiddling with gimmics.
Reply With Quote
  #4  
Old 09-27-2011, 08:49 AM
Platinum Member
 
Join Date: Feb 2007
Location: Townsend, Montana.
Posts: 7,620
Re: Help! Case neck runout...bent decapping rod?

Here is my experience over many years of reloading with many die types.

All expander balls have induced runout for me. However if the die is custom ground for your brass to only down size a limited ammount it will be better. Or you can simply adjust this with a bushing die by selecting the proper bushing. Also the option of not using an expander at all is a good choice the bushing die will allow.

With the Lee collet dies I have used I had problems getting enough neck tension. This was an issue even after many attempts to get it properly adjusted. Maybe I needed a smaller inside mandrel but I could not get a good feeling about the vertical creases the Lee collet leaves on my case necks so I went to the bushing dies and have found them to be awesome.

I size in two steps. First the necks where I get consistant neck tension of .002" Then I use a body die that alows me to size the body and only bump the shoulde back about .0015"

The result is very consistant cases both in neck tension and with all the shoulders at the same place. Which allows for very consistant bolt closure and opening after firing even in warmer weather.

My total indicated runout of a loaded round, checked at the o-give of the bullet, averages .0005" to .001" and more are to the lesser side of that.

Many ways to skin a cat, but this is working well for me and my ES and ELR groups are as tight as I have ever had.

Jeff
__________________
Reply With Quote
  #5  
Old 09-27-2011, 11:58 AM
Bronze Member
 
Join Date: Jul 2011
Location: manitoba, canada
Posts: 80
Re: Help! Case neck runout...bent decapping rod?

thanks for the replies guys.....

Gene... i took the decapping rod and rolled it in my concentricity gauge and i was getting about 2 thou runout on the expander button (round carbide button that sits about an inch above the decapping assembly) it wasnt obvious to the naked eye.... cant understand how 2 thou on the expander translates into 10 to 15 on the neck but i digress....

so that is two votes redding bushing dies and one vote lee collet die, and i take it a NO on just using the FL die without the expander and letting the bullet do the expansion ( dang i was hoping i could get away with that atleast in the short run as i wanted to get up and running with the new lapua brass right away) oh well i will just wait till i get back to the city and see if the guy i usually get my redding stuff from has a set of bushing dies....

i have heard good things about the lee collet dies from guys but have never used one before and to be honest the only lee dies i have used i was less than impressed with... they were just the regular lee dies in 223 my cousin got for his gun and he got them because they were the cheapest.

i am not too sure i want to go the route of neck sizing then running them through a body die to bump the shoulder in a two step process so i guess a redding series A full length bushing die would be the way to go....

thanks

orch
Reply With Quote
  #6  
Old 09-27-2011, 12:50 PM
Platinum Member
 
Join Date: Feb 2007
Location: Townsend, Montana.
Posts: 7,620
Re: Help! Case neck runout...bent decapping rod?

Quote:
Originally Posted by orch View Post
i am not too sure i want to go the route of neck sizing then running them through a body die to bump the shoulder in a two step process so i guess a redding series A full length bushing die would be the way to go....

thanks

orch
Yes, get the FL bushing die and if you ever get the urge to try the two step process you simply buy a comp neck bushing die and take all the guts out of your FL die you already have, and it becomes a Body only die. If you study the difference between the plain FL bushing die and the Neck die you will see that the comp neck die fully captures the case in a retractable sleeve before it sizes the neck. This I feel keeps everything true to the bushing and the result is straighter necks.

I should also add with the two step method you have the option to only neck size in one easy, no lube step using a titanium bushing. Until the shoulders grow to the point they do need bumped.


Also I might suggest you try this with your present die. Leave the expander stem loose with a small O-ring under the lock nut only finger tight. Then lube the inside of the necks a bit. This will allow the stem and expander ball to self center upon extraction. It may help. But will add the step of cleaning the excess lube out after.

I feel the reason you are getting this runout is from the die oversizing the necks down. Then the expander gets pretty hard to extract through your necks. Also if the necks are not consistant in thickness all the way around, the neck puls to the thinner side and induces a pulled crooked neck.

Jeff
__________________
Reply With Quote
  #7  
Old 09-27-2011, 02:39 PM
Bronze Member
 
Join Date: Jul 2011
Location: manitoba, canada
Posts: 80
Re: Help! Case neck runout...bent decapping rod?

Quote:
Originally Posted by Broz View Post
I feel the reason you are getting this runout is from the die oversizing the necks down. Then the expander gets pretty hard to extract through your necks. Also if the necks are not consistant in thickness all the way around, the neck puls to the thinner side and induces a pulled crooked neck.

Jeff
jeff i think you are dead on in your diagnosis of my problem! i measured the OD of the necks on some sized cases without the expander and i am getting about 5 thou smaller diameter than with the expander in... so i am guessing the brass is getting moved 8 thou or so when you take your sping back of 2 thou into account each way... so yah that die is squeezing that brass down quite a bit... and it does take a bit of a pull to get that ram back down as the expander pulls back out...

i switched to the lapua brass in the 308 because i was impressed with my 338 lapua brass's neck thickness consistancey so i hope it isnt inconsistent neck thickness (i was really hoping to avoid having to neck turn this stuff)

i did try the die with the stem loose and with lube in the inner neck and it showed no improvement...

only neck sizing is pretty much what i am doing with my fl die as it is... its a savage that i swap barrels in and when i set the headspace when i put the barrel on i headspace it to minimum speck so the fl die was only bumping the shoulder back about 1 thou from the fired case dimension... so i may as well just go with a fl bushing die.... i have one for my 338 lapua and have been really happy with it so i may as well just follow suit with the 308....

orch
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Help! Case neck runout...bent decapping rod?
Thread Thread Starter Forum Replies Last Post
Checking case wall runout milanuk Reloading 12 01-24-2009 07:55 PM
300 Rum case runout toklat04 Reloading 1 07-30-2008 06:58 PM
Case and Loaded Round Runout question dlebeck Reloading 8 05-21-2006 12:37 PM
neck runout with redding bushing dies??? JustC Rifles, Bullets, Barrels and Ballistics 13 12-24-2004 06:24 PM
Case Runout Brent Rifles, Bullets, Barrels and Ballistics 10 10-25-2003 11:39 PM

Current Poll
How Many Different Cartridges Do You Reload For?
ZERO, all factory ammo - 8.07%
328 Votes
1 - 2.86%
116 Votes
2 or 3 - 14.55%
591 Votes
4 or 5 - 20.48%
832 Votes
6 or 7 - 14.55%
591 Votes
8 or 9 - 8.86%
360 Votes
10 or more - 30.63%
1,244 Vote
Total Votes: 4,062
You may not vote on this poll.

All times are GMT -5. The time now is 05:49 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC