Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

Good 25-06 brass?

 
LinkBack Thread Tools Display Modes
  #1  
Old 11-13-2009, 08:56 AM
Silver Member
 
Join Date: Dec 2008
Posts: 178
Good 25-06 brass?

My dad has shot a 25-06 for years, and I'm thinking about getting one. What do you all think of the brass available, any recomendations or warnings? I'm willing to pay for quality brass, and wondering how many loadings to expect.
Reply With Quote
  #2  
Old 11-13-2009, 12:50 PM
Gold Member
 
Join Date: Jan 2007
Location: Fairfax County, Va
Posts: 699
Re: Good 25-06 brass?

A lot depends of how much work you are willing to do, probably the best would be Lapua 30-06 and then you would have to have and S-bushing die with several bushings to get it down to 25 cal, or if you had access to a 280 die and a 270 die and then the 25-06 that would probably work.
You may also have to turn the necks because they will be fairly thick by the time you size them from 30cal to 25 cal.
Depending on how hot you load them and whether or not you anneal the necks every 3 to 4 shots you could get 5 to 15 firings on the Lapua.
If you just want to buy the brass and load them, then I would use Winchester, you will probably get about half as many loads out of the Winchester under the same conditions.
Powder Valley has both in stock at reasonable prices
JMHO
Dave
Reply With Quote
  #3  
Old 11-13-2009, 01:21 PM
Platinum Member
 
Join Date: May 2008
Location: South of Canada and North of Wyoming
Posts: 5,953
Re: Good 25-06 brass?

I agree with Dave except i think you will get a whole lot more than 15 reloads with the Lapua brass in a 25-06, I would expect 40 plus, especially if you use bushings to size.

Right now I am using Winchester and accuracy out of my 25-06 Sendero is great. I just use a FL sizer and back it off a little to leave a donut around the bottom of the neck and just bump the shoulder and body back a little. works great. If doing that way, i would recoomend using a floating expander button with rubber 'o' ring to get more concentric necks... haven't doen this yet and am considering going FL bushing die and Lapua .06 brass.

Cheers,

Mark
Reply With Quote
  #4  
Old 11-13-2009, 09:04 PM
Junior Member
 
Join Date: Aug 2008
Posts: 10
Re: Good 25-06 brass?

I have a sendero that I bought in 2001, I shoot a 100gr Nosler Ballistic tip at 3400 fps and I use Rem and Win brass (the cheap stuff). I only neck size and I have got the same 100 brass, and I know I have over 15 reloads with them. The gun still shoots bug hole groups @ 100yds.
Reply With Quote
  #5  
Old 11-15-2009, 01:07 AM
GNERGY
 
Posts: n/a
Re: Good 25-06 brass?

When I built my 25-06 back in 1970 it was still a wildcat. I got once fired 30-06 military brass and necked them down. It would shoot under .375 groups with Sierrs 87gr. HPBT all the time. My best 5 shot group was .204
I didn't know anything about all this brass prep that goes on now.
It has a 28 inch Mcgowan barrel on it.
Tarey
Reply With Quote
  #6  
Old 11-15-2009, 10:29 AM
Silver Member
 
Join Date: Nov 2009
Posts: 301
Re: Good 25-06 brass?

I prefer to reform military 30-06 brass for my 25-06. The "Greek" brass with the HXP head stamp works well for me. I get it for free at the range, all I have to do is bend down and pick it up. I do the re-forming all in one step with my Lyman 25-06 FL size die, trim, then fire form, then neck size with the Lee Collet Neck die. I have to bump the shoulder back periodicly but I get very consistent results in my Ruger #1V. I had a stash of new factory brass but sold it all because I like the re-formed brass better. I've been re-forming for my gun for about 5 years now and not a single problem. My guns chamber does not require me neck turn the re-formed brass. I had a slight problem with blow back (case neck and shoulders turning black from ignited powder) with factory brass but that has gone away with my re-forms. I think the slight increase in neck wall thickness worked to my advantage with my gun.
Reply With Quote
  #7  
Old 11-15-2009, 07:57 PM
Silver Member
 
Join Date: Nov 2004
Location: Michigan
Posts: 218
Re: Good 25-06 brass?

I use Norma 270 brass to fire form into 25-06AI. Simple process and I've managed to get four loads thus far but I do anneal after F/F. Norma has a bad rap for being sof but I have no complaints in either my 25-06AI or 204.
__________________
QDMA Member
7STW Club
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Good 25-06 brass?
Thread Thread Starter Forum Replies Last Post
Who makes good brass for the 7mm rem mag? 188MULE Reloading 12 01-26-2010 12:08 AM
Good brass for 300 win mag? hillajam Reloading 25 03-07-2007 08:26 AM
Nosler Brass cosmetic seconds good brass? sambo3006 Reloading 6 01-04-2007 08:57 PM
Brass still good to go ? Jimm Reloading 7 06-08-2006 08:02 PM
Good Brass for 300 RUM David Hunter Rifles, Bullets, Barrels & Ballistics 2 02-26-2003 02:25 PM


All times are GMT -5. The time now is 08:22 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC